We have investigated the use of microwave heating and radiometry to safely heat urine inside a pediatric bladder. The medical application for this research is to create a safe and reliable method to detect vesicoureteral reflux, a pediatric disorder, where urine flow is reversed and flows from the bladder back up into the kidney. Using fat and muscle tissue models, we have performed both experimental and numerical simulations of a pediatric bladder model using planar dual concentric conductor microstrip antennas at 915 MHz for microwave heating. A planar elliptical antenna connected to a 500 MHz bandwidth microwave radiometer centered at 3.5 GHz was used for noninvasive temperature measurement inside tissue. Temperatures were measured in the phantom models at points during the experiment with implanted fiberoptic sensors, and 2-D distributions in cut planes at depth in the phantom with an infrared camera at the end of the experiment. Cycling between 20 s with 20 Watts power for heating, and 10 s without power to allow for undisturbed microwave radiometry measurements, the experimental results show that the target tissue temperature inside the phantom increases fast and that the radiometer provides useful measurements of spatially averaged temperature of the illuminated volume. The presented numerical and experimental results show excellent concordance, which confirms that the proposed system for microwave heating and radiometry is applicable for safe and reliable heating of pediatric bladder.

Synthetic aperture focusing techniques (SAFT) have already been studied within several fields of non-destructive testing, but so far only with a single, relatively homogenous medium. In this article, we modify the original time-domain SAFT in order to image the interior of a multilayer structure. Standard focusing techniques assume that the wave velocity is constant within the volume to be imaged. The concept of the root-mean-square (RMS) velocity is used here to modify the classical delay-and-sum algorithm to handle layers with differing wave velocities. A scheme for iteratively using this to estimate the interfaces between the layers is also presented. The proposed method is demonstrated on ultrasonic B-scans of two test objects immersed in water, and it is shown that the increased lateral resolution and signal-to-noise ratio of standard SAFT is extended to the multilayer case. The increased resolution also makes it possible to accurately estimate the interfaces between consecutive layers, as long as the preceding interfaces are relatively smooth.

The exploitation of offshore wind resources is a crucial step towards a clean energy future. It requires an advanced approach for high-resolution wind resource evaluations. We explored the suitability of the Sentinel-1 Level-2 OCN ocean wind field (OWI) product for offshore wind resource assessments. The SAR data were compared to in situ observations and three reanalysis products: the global reanalysis ERA5 and two regional reanalyses CARRA and NORA3. This case study matches 238 scenes from 2022 for the Goliat station, an oil platform located 85 km northwest of Hammerfest in the Barents Sea, where a new offshore wind park has been proposed. The analysis showed that despite their unique limitations in spatial and temporal resolutions, all data sources have similar statistical properties (RMSE, correlation coefficient, and standard deviation). The Weibull parameters characterizing the wind speed distributions showed strong similarities between the Sentinel-1 and all reanalysis data. The Weibull parameters of the in situ measurements showed an underestimation of wind speed compared to all other sources. Comparing the full reanalysis datasets with the subsets matching the SAR scenes, only slight changes in Weibull parameters were found, indicating that, despite its low temporal resolution, the Sentinel-1 Level 2 OWI product can compete with the more commonly used reanalysis products in the estimation of offshore wind resources. Its high spatial resolution, which is unmatched by other methods, renders it especially valuable in offshore areas close to complex coastlines and in resolving weather events at a smaller scale.

This paper investigates both numerically and experimentally the spatio-temporal effects of water flow in a custom-made water bolus used for superficial hyperthermia generated by a 915-MHz, 4 x 3 microwave applicator array. Similar hyperthermia models referenced in the literature use a constant water temperature and uniform heat flux to describe conduction and convection energy exchange within the heating apparatus available to cool the tissue surface. The results presented in this paper show that the spatially varying flow pattern and rate are vital factors for the overall heat control applicability of the 5 mm thick bolus under study. Regions with low flow rates and low heat convection clearly put restrictions on the maximum microwave energy possible within the limits of skin temperature rise under the bolus. Our analysis is illustrated by experimental flow front studies using a contrast liquid set-up monitored by high definition video and complemented by numerical analysis of liquid flow and heat exchange within the rectangular water bolus loaded by malignant tissue. Important factors for the improvement of future bolus designs are also discussed in terms of diameter and configuration of the water input and output tubing network.