Jet pump cavitation reactors (JPCRs) have significant potential to be used in water treatment applications. During their operation, the hydroxyl radicals generated by cavitation collapse produce a strong oxidation capacity, which is one of the key mechanisms in disrupting algal cells. In this paper, we investigate the hydroxyl radicals produced by single cavitation bubble in a JPCR. The numerical method includes a bubble dynamic model, molecular diffusion model, energy balance equation, and chemical reaction model for predicting the hydroxyl radical production. Additionally, the pressure distribution within a JPCR is tested and used to analyze the single-bubble performance. The effects of the JPCR operating conditions and structure parameters on hydroxyl radical production are further discussed. Our results indicate that, when the flow rate ratio is positive, the number of hydroxyl radicals is closely related to the development and collapse of the cavitation bubble and reaches a peak value under the critical condition. When the flow rate ratio is negative, the maximum production of hydroxyl radicals appears under backflow stagnation condition. In general, increasing the throat length–diameter ratio and diffuser angle encourages the production of hydroxyl radicals, whereas increasing the area ratio inhibits their generation.
The annular jet pump (AJP) has garnered significant attention in nondestructive conveying, but cavitation can severely impact its performance. Large Eddy simulation was used to investigate the unsteady three-dimensional cavitating flow in an AJP under various operating conditions. The results, validated against experimental data, revealed the onset and evolution of shear cavitation at low flow ratios and low-pressure cavitation at high flow ratios. The results show that cavitation under low flow ratios mainly occurs in the suction chamber's shear layer, initially forming a ring-shaped structure dominated by intense shear effect between high-speed primary flow and low-speed secondary flow. The evolution of ring-shaped cavitation demonstrates clear periodicity, progressing through four distinct stages: initiation, twisting deformation, recirculation, and collapse, with its development closely linked to vortex structure evolution. Under large flow ratios, cavitation primarily develops in the throat and diffuser, manifesting as two distinct types: (1) jet shear layer cavitation induced by vortex structures and throat low pressure and (2) wall shear cavitation driven by boundary layer effects. In contrast to low flow ratio conditions, cavitation at large flow ratios exhibits no clear periodicity but remains strongly correlated with vortex structure evolution, particularly in the diffuser, where cavitation collapse coincides with vortex formation. Furthermore, analysis of the vorticity transport equation revealed a strong coupling between cavitation and vortex structure, with cavitation significantly impacting vorticity distribution and generation. The results indicate that the vortex stretching term is the primary contributor to vorticity transport, while the baroclinic torque term exhibits strong spatial correlation with cavitation.
20 June 2025 in Journal of Environmental Management
Electro-Hydraulic Proportional Directional Valve (EHPDV) is a key component in an electro-hydraulic proportional control system. Erosion-abrasion caused by solid particles within the oil is one of the major concerns in hydraulic control valves which may result in equipment malfunction and even failure. In this paper, the erosion-abrasion of a sliding spool of EHPDV was researched through Computational Fluid Dynamic (CFD) simulation and the analysis consists of three steps: the continuous phase flow field simulation, particle tracking, and erosion calculation. Therefore, a three dimensional model of the valve was built and the grid was meshed by use of ICEM. Then, a coupled Eulerian-Lagrangian approach was employed to solve the liquid-particle flow characteristics within the EHPDV, the Erosion/Corrosion Research Center (E/CRC) erosion model and the Grant empirical formula of particle-wall rebound models were utilized to predict the erosion rate. The simulation results indicated that the average erosion rate of the sliding spool would nonlinearly various with the valve opening. In addition, the maximum and average erosion rate of the sliding spool would gradually increase with the velocity. 10 µm is the critical diameter, and the erosion rate would decrease with the increases of the particle diameter if the particle diameter is above 10 µm and inversely when the diameter is below 10µm. Based on the simulation results, an erosion prediction model of sliding spool was further proposed, which provides a theoretical principle for forecasting the lifecycle of EHPDV.
Helical coil heat exchanger has been widely used in hydraulics engineering, and plays an important role in modern industry. The distribution of fluid field which would be influenced by helical coil structural parameters is an important factor affecting its thermal performance. In this paper, CFD analysis is conducted to study the effects of the inlet flow, the mid-diameter of coils, the pitch, and the number of helical coil turns on the thermal performance of a heat exchanger. Results show that the outlet temperature and pressure drop of the helical coil heat exchanger are affected significantly by the inlet mass flow rate, and varies with the mid-diameter and pitch. And it approximately linearly increases with the number of coil turns.