Mohd Raizamzamani Md Zain

Dr. Mohd Raizamzamani Md Zain


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2021 in Construction and Building Materials
Verified
Journal Article
Closed access
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
OLOh Chai Lian
Oh Chai Lian
SLSiong Wee Lee
Siong Wee Lee

8 November 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SLS W Lee
S W Lee
OLOh Chai Lian
Oh Chai Lian
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
NYN A Yahya
N A Yahya

1 August 2018 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
LWLee Siong Wee
Lee Siong Wee
OLOh Chai Lian
Oh Chai Lian
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
This paper investigates the mechanical properties of engineered cementitious composites (ECC) in terms of compressive strength and flexural behaviour. A new version of ECC made of cement, ground granulated blast-furnace slag (GGBS), local sand, polypropylene (PP) fibers, water and superplasticizer (SP) was employed in this study. Few series of ECC mixtures were designed, cast, and tested in compression and flexural after 28 days of curing. The effect of the fiber content and sand content were studied in different cement-GGBS combination. Compression test results indicated that all ECC mixtures obtained at least 1.8 times compressive strength compared to normal concrete. They also demonstrated more ductile flexural behavior compared to normal concrete from three-point bending test. Increasing fiber content from 1.5% to 2.0% and 2.5% has negative effect on compressive strength but significantly improved modulus of toughness of ECC mixtures. The compressive strength of ECC was reduced when the sand to binder ratio adjusted to 0.4 and 0.6. The flexural behaviour of ECC was slightly improved with the increasing of sand content.

29 June 2019 in Asian Journal of Civil Engineering
Verified
Journal Article
Closed access
PDF file
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
AAA. R. Azerai
A. R. Azerai
AHA. H. Hanizah
A. H. Hanizah

11 December 2018 in MATEC Web of Conferences
Verified
Journal Article
Open access
COCl Oh
Cl Oh
SLSw Lee
Sw Lee
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
AAAr Azerai
Ar Azerai
YAY Norrul Azmi
Y Norrul Azmi
Development of high strength concrete as a new ecological construction material to sustain the gradually expanding construction industry has arisen. This paper presents nonlinear finite element analysis of three-dimensional high strength reinforced concrete beams using ABAQUS. The uniaxial compressive strength for the beam models were taken from the existing experimatal data on high strength concrete cubes. Eurocode 2 was also used to establish material parameters for the constitutive models for concrete and reinforcing bars. In this study, two 150mm x 200mm x 1200mm simply supported rectangular concrete beam models subjected to loads at different shear span to effective depth ratios (a/d = 1.0 and 2.0) were analysed. Numerical results were validated with the existing experimental data specifically on the load-deflection responses and von mises stresses. It was found that the finite element results show greater than 70% agreement with the experimental results.

29 November 2018 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
OLOh Chai Lian
Oh Chai Lian
KCK K Choong
K K Choong
TNT Nishimura
T Nishimura
JKJ Y Kim
J Y Kim
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
Tensegrity consisting pinned-jointed struts and cables is lightweight and flexible. Extensive research works on the shape change of tensegrity, especially the deployable tensegrity structures and tensegrity robots have been carried out. This paper presents the structural characteristics of a tapered three-stage tensegrity model during shape change analysis by using a shape change method. The method employed sequential quadratic programming in the optimization of forced elongation in cables, such that the model can advance to the targets. Structural characteristics of the tapered tensegrity model were examined under various displacement schemes. It was found that the tensegrity model demonstrated bending, axial and torsional deformations during the shape change analysis.