Lee Siong Wee

Lee Siong Wee

Auto-generated profile, based on publicly available information

Lee Siong Wee

School of Civil Engineering, College of Engineering, Universiti Teknologi MARA, 81750, Masai, Johor, Malaysia

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2016 in Construction and Building Materials
Verified
Journal Article
Closed access
SLSiong Wee Lee
Siong Wee Lee
SKShao-Bo Kang
Shao-Bo Kang
KTKang Hai Tan
Kang Hai Tan
EYEn-Hua Yang
En-Hua Yang

8 November 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SLS W Lee
S W Lee
OLOh Chai Lian
Oh Chai Lian
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
NYN A Yahya
N A Yahya

1 August 2018 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
LWLee Siong Wee
Lee Siong Wee
OLOh Chai Lian
Oh Chai Lian
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
This paper investigates the mechanical properties of engineered cementitious composites (ECC) in terms of compressive strength and flexural behaviour. A new version of ECC made of cement, ground granulated blast-furnace slag (GGBS), local sand, polypropylene (PP) fibers, water and superplasticizer (SP) was employed in this study. Few series of ECC mixtures were designed, cast, and tested in compression and flexural after 28 days of curing. The effect of the fiber content and sand content were studied in different cement-GGBS combination. Compression test results indicated that all ECC mixtures obtained at least 1.8 times compressive strength compared to normal concrete. They also demonstrated more ductile flexural behavior compared to normal concrete from three-point bending test. Increasing fiber content from 1.5% to 2.0% and 2.5% has negative effect on compressive strength but significantly improved modulus of toughness of ECC mixtures. The compressive strength of ECC was reduced when the sand to binder ratio adjusted to 0.4 and 0.6. The flexural behaviour of ECC was slightly improved with the increasing of sand content.

1 November 2019 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
SLS W Lee
S W Lee
RHRohana Hassan
Rohana Hassan
NSN Saari
N Saari
NMN M Mohamad
N M Mohamad
NNN I Mat Noor
N I Mat Noor
The flexural behaviours of reinforced concrete (RC) beams incorporating steel and polypropylene fibres under four-point bending test is examined in this paper. A total of nine beam specimens were designed, cast and tested under flexural loadings. Three types of concrete mixture – plain, concrete with steel fibres and concrete with polypropylene fibres – were employed in this study. Fibre content is fixed at 3% by the weight of sand as sand replacement for both mixtures containing either steel or plastic fibres. Compression tests were also conducted at 7, 14 and 28 days for twenty-seven concrete cubes prepared using the three mixtures. Comparisons of results were done in term of compressive strength, ultimate flexural load and deflection capacity. The crack pattern and failure mechanism of RC beams subjected to four-point bending are discussed. Finally, the effect of steel and polypropylene fibres on the flexural behaviour of RC beams are justified.

17 September 2024 in Jurnal Teknologi (Sciences & Engineering)
Verified
Journal Article
Open access
PDF file
NRNur Hazira Rosli
Nur Hazira Rosli
SYSyed Muhammad Syed Yahya
Syed Muhammad Syed Yahya
LWLee Siong Wee
Lee Siong Wee
TNToku Nishimura
Toku Nishimura
OLOh Chai Lian
Oh Chai Lian
The study presents the axial deformation of a spine bio-tensegrity model through a shape change strategy with different deployment schemes. The spine bio-tensegrity model mimics the total height, tapered form and natural curvature of a human spine. Three deployable schemes S1-S3 with a different combination of cables at alterable and fixed lengths (at the lower, middle and upper part of the model, respectively) were investigated to achieve a series of axial displacements at 200 mm, 400 mm and 600 mm in the z-direction. The shape change algorithm was developed to optimise the forced elongation of cables, incorporating an objective function designed for monitored nodes in the system to reach their prescribed targets during the optimisation process. Sequential quadratic programming was employed to solve a nonlinear optimisation problem in the shape change analysis involving inequality constraints. The efficiency of the deployable schemes was evaluated based on the deformed shapes, convergence curve and axial forces of the spine bio-tensegrity model. The finding shows in addition to axial deformation, the model in deployment scheme S1 preserves the slenderness characteristic of the spine. In contrast, the model exhibits excessive expansion in the thoracic region in schemes S2 and S3. Greater total computational steps in deployment scheme S3, followed by S2 and S1, reveal that the active cables set near the monitored nodes allow the model to sense and act faster to reach their targets. The study contributes to understanding the structural behaviour and deployment strategy for a structure mimicking a biological system.

1 December 2010
Verified
Conference Paper
Closed access
MZMohd Raizamzamani Md Zain
Mohd Raizamzamani Md Zain
LWLee Siong Wee
Lee Siong Wee
MRM. Ikmal Fazlan Rosli
M. Ikmal Fazlan Rosli
HHHanizah Ab. Hamid
Hanizah Ab. Hamid
Cold-formed steel channel sections had been widely recognized as lightweight material and its application in construction industry seen to be unlimited because it has proven in minimizing the building cost while satisfying the required strength. This paper investigates the structural behavior of cold-formed steel channel columns (without or with stiffeners) subjected to axial thrust. Computer aided analyses were used in order to determine the required results such as ultimate loads, deflections, load-displacement relationships and the failure modes. A total of nine (9) models were adopted to compare the performance of different shapes of channel sections at various lengths (500mm, 750mm and 1000 mm). Results from finite element analysis agree well with the British Standard and previous researcher ultimate loads. The results indicate that the channel sections with intermediate stiffener are superior in terms of ultimate load among the three shapes at the same column length. On the other hand, the stub columns have the greater load capacity compared to the slender columns. Nevertheless, all column sections failed in local buckling and the channel sections with stiffeners has shown a less deform in terms of buckling.