Farid Dwi Murdianto

Mr. Farid Dwi Murdianto


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 June 2018 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
MEMoh. Zaenal Efendi
Moh. Zaenal Efendi
SUSuhariningsih
Suhariningsih
FMFarid Dwi Murdianto
Farid Dwi Murdianto
EIEvi Inawati
Evi Inawati
Photovoltaic (PV) module is used to convert solar energy to electrical energy. The output power of PV module is affected by the amount of irradiation of sun and temperature of PV module. The problem that may occur is partial shading caused by some objects such as trees, building, clouds, and so on. The impact of this condition is the decrease of output power of PV and the maximum power point (MPP) become more than one. Maximum power point of P-V characteristic curve will be more than one such as GMPP (Global Maximum Power Point) and LMPP (Local Maximum Power Point). This case cannot be solved using the ordinary MPPT (Maximum Power Point Tracking) method because the maximum power is trapped on wrong point, it is LMPP. Therefore, to overcome this problem, Modified P&O (Perturb and Observe) method is proposed as a MPPT method under partial shading condition. The proposed method is implemented on SEPIC converter to get actual maximum power point (GMPP). Experiment results prove the Modified P&O method can generate greater power and faster charging process on battery. The State of Charge of battery increases about 30% if the Modified P&O method, which is applied on battery charging system.

1 March 2021 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MKM B Kurniawan
M B Kurniawan
MEM Z Efendi
M Z Efendi
FMFarid Dwi Murdianto
Farid Dwi Murdianto
This Paper is explain about how to design a Multilevel Boost Converter (MLBC). This Converter is a Boost Converter with an upgrade of Parallel Diode Circuit and Capacitors Circuit. MLBC (Multi Level Boost Converter) have more advantages with low voltage input change to high voltage output. The Principle of MLBC is like the Boost Converter, but they have high ratio conversion without adding transformation for step up the voltage, the setting Output will stabilize if they always get the minimum input range for reduce the drop voltage from input who used Solar Panel, it is used MISO (Multiplied Input Single Output), the MISO contains Solar Panel and Battery with the parallel circuit set. DC Micro Grid using as DC BUS for distributed the voltage from the source to load for the maximum output power it used 100-200 Watt. The Method of control voltage it used PI - Ziegler Nichols-1 for controlled the Multi Input Single Output (MISO) block, the first control used to make the input of MLBC stabilize for 30 - 40 V being step up to 200 - 250 Volt. The Load of DC BUS example: Inverter, 3 Phase Motor, Led DC, Battery Energy Storage at this project used a inverter with 3 phase motor for load of converter. The Maximum Output Power from a design of this converter is 234.87 Watt according the DC load and the efficiency of converter is maximum 86 %.

6 October 2025 in Engineering, Technology & Applied Science Research
Verified
Journal Article
Open access
PDF file
IRIrianto
Irianto
AAAhmad Firyal Adila
Ahmad Firyal Adila
FMFarid Dwi Murdianto
Farid Dwi Murdianto
MFMuhammad Azumardi Fahmi
Muhammad Azumardi Fahmi
The use of Variable Frequency Drives (VFDs) is unavoidable, especially in the industrial sector, where motor speed regulation is required to expedite production. VFDs are included in nonlinear loads, which, when in use, can cause the voltage and current of the source to differ. When a source carries a nonlinear load, the current distorts, resulting in a non-sinusoidal shape. The degree of distortion, Total Harmonic Distortion (THD), shows that as THD increases, the signal becomes more distorted. To reduce the distorted source currents, active harmonic filters are used and arranged in parallel between the source and the load. The active harmonic filter works by producing a harmonic current that eliminates the distorted source current, which is achieved by extracting the current distortion signal using the multiplication-with-sine-function method. When the mesh source is loaded with a VFD, the THD of the source current is 45.35%. According to the 2014 IEEE-519 standard, the maximum THD value of the current should be 5%, which is not met, so an active harmonic filter is installed. After installing the active harmonic filter, the THD of the current dropped to 3.57%. This was achieved with a VDC setpoint of 500 V, stabilized by Proportional Integral (PI) control with a P value of 17.543 and I value of 0.00018.