To examine the effects of ferritic steel on error field, ripple reduction and plasma properties (especially for improved confinements), Advanced Material Tokamak EXperiment (AMTEX) is planned for JFT-2M. The AMTEX program consists of the test of toroidal field ripple reduction with ferritic inserts and that of the compatibility between ferritic steel and the tokamak plasma. To reduce fast ion losses due to toroidal field ripple, the ripple amplitude and its toroidal mode number have to be reduced. The guideline of the design for the reduction in ripple amplitude (δ) by inserting Ferritic Boards (FB) is as follows; the wider and thicker FB should be positioned far from the plasma and be located just under the toroidal field coil. Elimination of a central part of the FBs is effective in reducing a second harmonic ripple amplitude. Since the ferritic steel easily saturates by the toroidal magnetic field, the δ depends on the toroidal magnetic field. The JFT-2M Vacuum Vessel (VV) will be remodelled using ferritic steel for the plasma-matching test. Since the relative magnetic permeability of the ferritic steel is around two, the effect of the ferritic steel VV on plasma equilibrium is rather small. A simple port design can reduce any ripple amplitude of the fundamental mode but cannot reduce that of higher modes.
Humidity measurement is required in various fields. We previously developed a sensor that leverages the sudden change in the transmitted light intensity when switching from leakage mode to waveguide mode. By adjusting the low-refractive-index polymer of the cladding, we achieved measurements at 60% RH. However, for practical use, measurements at low humidity are essential. Therefore, in this study, we developed a sensor using a leakage mode that enables measurements at low humidity. To measure the leakage mode, it is necessary to increase the absorbance of the cladding and the incident angle at the core–cladding interface. Therefore, we developed a sensor in which the core was stretched, and the cladding was doped with a high concentration of dye. The experimental results confirmed that a sensor with a polymer concentration of 4% and a dye concentration of 3% could measure from 0% RH to 95% RH. The sensitivity was 0.1 dB/% RH from 0% RH to 70% RH and 0.32 dB/% RH from 70% RH to 95% RH. The estimated response time for a change from 10% to 90% light transmission for a sensor with 4% polymer concentration and 0.5% dye concentration was 22 s from 45% RH to 0% RH and 50 s from 0% RH to 45% RH.
Because humidity is an important indicator used in many fields, the development of technology for its measurement is of great significance. We investigated humidity sensors that use a swellable polymer as the cladding material of plastic optical fibers. A plastic optical fiber humidity sensor using hydroxyethylcellulose as the cladding material has a linear response at approximately 20% relative humidity, but its sensitivity is low. The sensitivity can be improved by adding brilliant blue as a dye to the cladding. However, this makes the detection range of the sensor too narrow for practical use. Therefore, we change the incident light from a single wavelength to two wavelengths and use the fact that the output waveform of the dye-doped sensor depends on the wavelength of the incident light. The results of experiments show that a humidity sensor with high sensitivity and a relative-humidity detection range of 10–90% can be developed by combining the output waveforms of a two-wavelength sensor with a dye doping level of 0.8% in the cladding.
Increasing the export of fruit is vital for the Japanese economy. In this study, we focused on the peach trade as it is the third most transported fruit in Japan. The peach is a very sensitive fruit; therefore, proper packaging is important. We proposed a special packing sheet that we named the “concavo-convex sheet” developed through a simple mechanism. However, there were some problems in creating this sheet. This study describes the new mechanism for creating the concavo-convex sheet, and a real machine using the installed mechanism was developed. As a result, it was confirmed that the sheet can be realized by the new machine.