Core-shell-type catalysts, which are synthesized by encapsulating the Cu-ZnO-Alumina type methanol synthesis catalyst (CZA) by silicotungstic acid (STA)-incorporated mesoporous alumina, were prepared following a hydrothermal route and tested in DME synthesis from syngas and CO2. Activity tests, which were performed in the pressure range of 30–50 bar, and the temperature range of 200–300 °C, with different feed compositions (CO2/CO/H2: 50/-/50, 40/10/50, 25/25/50, 10/40/50) showed that the best-operating conditions for the highest DME yield were 275 °C and 50 bar. Results proved that the presence of CO2 in the syngas had a positive effect on the DME yield. The total conversion of CO + CO2 increased with an increase in CO2/CO ratio. An overall conversion of CO + CO2 and DME selectivity values were obtained as 65.6% and 73.2%, respectively, with a feed composition of H2/CO2/CO = 50/40/10. Synthesis of methanol using the CZA catalyst from the CO2-containing gas mixtures was also investigated, and the total conversion of CO + CO2 and methanol selectivity values of 32.0% and 83.6%, respectively, were obtained with the H2/CO2/CO = 50/40/10 gas mixture. Results proved that the new STA incorporated core-shell-type bifunctional catalysts were highly promising for the conversion of CO2-containing syngas to DME.
Bio-oil obtained through the gasification or pyrolysis of biomass is a renewable energy source with the potential to be used in motor vehicles. However, when the properties of bio-oil are compared to crude oil, bio-oil is observed to have high oxygen content and acidity. The aim of this study is to enhance the physical properties of bio-oil and produce new alternative fuels to crude oil. For this purpose, nickel and cobalt-incorporated mesoporous HZSM-5 catalysts have been synthesized. The synthesized catalysts were characterized by X-ray diffraction, N2 adsorption–desorption, Scanning electron microscopy energy dispersive spectroscopy, Inductively coupled plasma optical emission spectroscopy, Fourier-transformed infrared spectroscopy, and thermogravimetric/differential thermal analysis. In the study, formic acid, furfural, and hydroxypropanone were used as model components. To enhance catalyst activity, nickel was loaded onto the HZSM-5 catalyst. However, during biofuel production, a significant amount of coke was formed as a by-product. Therefore, cobalt was impregnated to reduce coke formation. In the activity test studies, a conversion in the range of 77–84% was achieved with HZSM-5 catalysts. Nickel addition increased the paraffin and olefin content in the biofuel along with bio-oil conversion. The maximum paraffin selectivity (97%) was provided with the 5Ni@HZSM-5 catalyst. However, the highest biofuel selectivity (77.5%) with the minimum coke formation (4%) was observed with the 5Co-5Ni@HZSM-5. In the study, the regeneration and long-term catalytic activity were also investigated, and the results showed that 5Co-5Ni@HZSM is an attractive catalyst for biofuel production from bio-oil.
Chromium and molybdenum incorporated MgO and MgO–C catalysts were synthesized for hydrogen production from a non-oxidative ethane dehydration reaction. Hydrogen production studies were carried out using a microwave-heated reactor system. The study investigated the effects of reaction temperature, type of active metal, and catalyst preparation method (physical mixture or core–shell structure) on hydrogen selectivity and ethane conversion during dehydrogenation reactions. The results showed that the optimal reaction temperature for the non-oxidative ethane dehydration reaction was 450 °C. Above this temperature, the selectivity of undesired byproducts increased. Catalysts containing molybdenum exhibited higher ethane conversion. Moreover, a comparison of MgO–C-supported catalysts with MgO-supported catalysts revealed that the core–shell catalysts exhibited superior ethane conversion. Notably, the 5Mo@MgO–C catalyst demonstrated exceptional catalytic activity, achieving a high ethane conversion rate of 72% along with excellent stability.
30 December 2021 in Konya Journal of Engineering Sciences
In the present study, Ni-containing mesoporous aluminosilicate (Al2(SiO2)3) supported catalysts, which are resistant to carbon formation, were developed for hydrogen production from acetic acid. Commercial aluminosilicate (Al2(SiO2)3) was used as catalyst support. Furthermore, to improve the catalyst stability, Mg, La, Ce, Ca, Ru metals, and Ni (5% by mass) were incorporated by the wet impregnation method into the catalyst supports’ structure. The synthesized catalysts were characterized to define their physical and chemical properties. N2 adsorption-desorption results reveal that the resulting isotherm behavior of all the prepared catalysts is consistent with type IV isotherm with plate-like wall structures. The catalytic activity test of the prepared catalysts was investigated at a reaction temperature of 750 C and a feed molar ratio of 1/2.5 (AA/H2O) in a packed bed continuous reactor system. Activity test results showed that catalyst composition has profound effects on product distribution. Hydrogen-rich syngas was produced over 5Ni-3Ru@Al2(SiO2)3 and 5Ni-3CeO2@Al2(SiO2)3 (about % 44 and % 46, respectively) catalysts. However, the addition of MgO over the 5Ni@Al2(SiO2)3 catalyst strongly influenced the selectivity of hydrogen. Syngas, which contains an equimolar amount of H2, and CO is a quite important feedstock for the Fischer-Tropsch process (about 35% each), was obtained with the 5Ni-3MgO@Al2(SiO2)3 catalyst.
Çalışma kapsamında çay atığı hem aktif karbon (AC) hem de ileri mühendislik seramiği olan bor karbür (B4C) üretmek için kullanılmıştır. Türkiye’de büyük miktarlarda oluşan çay atıkları, düşük ekonomik değere sahip olmasına rağmen biyokütle tabanlı bir hammadde kaynağı olarak önemli bir potansiyel taşımaktadır. Çalışmanın ilk aşamasında, çay atıkları potasyum hidroksit (KOH) ile kimyasal olarak aktive edilmiş ve 1500°C’de karbonizasyon işlemi uygulanmıştır. Elde edilen AC; elementel analiz, yüzey alanı ve porozite analizi (BET, Brunauer-Emmett-Teller), Fourier dönüşümlü kızılötesi spektroskopisi (FTIR), termogravimetrik ve diferansiyel termal (TGA/DTA) ve X-Işını difraksiyonu (XRD) teknikleriyle karakterize edilmiş ve 1301 m2/g gibi çok yüksek bir yüzey alanı ile mikromezogözenek yapısına sahip olduğu belirlenmiştir. İkinci aşamada, sentezlenen AC borik asit (H3BO3) ile karbotermik indirgemeye tabi tutularak B4C sentezi gerçekleştirilmiştir. Yapılan analizler (XRD ve FT-IR), çay atığı kökenli AC kullanımıyla B4C’nin başarıyla sentezlendiğini göstermektedir. Sonuçlar, düşük maliyetli ve yerli atık kaynaklarının stratejik öneme sahip ileri mühendislik seramiklerinin üretiminde değerlendirilebileceğini göstermektedir. Böylece çalışma, yalnızca atıkların geri kazanımına katkı sunmakla kalmamakta, aynı zamanda sürdürülebilir malzeme bilimi açısından literatüre güçlü ve yenilikçi bir katkı sunmaktadır.