Control of Fe in Al alloys is a severe challenge for the full metal circulation to produce the recycled alloys with mechanical and physical performance as high as the primary alloys. The high restriction of Fe content is mainly due to the deterioration caused by the large-scale Fe-containing intermetallic compounds (FIMCs) in Al alloys. In this paper, recent knowledge gained regarding nucleation, formation, and technical developments on microstructural control and refinement of FIMCs are overviewed. Specific characteristics of the multiple types of FIMCs in Al alloys are presented in two- and three- dimensional (2D and 3D) form. Phase relationships between the FIMCs in different structures, such as primary phase, binary eutectic, and ternary eutectic, formed at different solidification stages are studied. Phase transformations between the FIMCs with or without intermediate phases during the solidification process are examined in different Al alloys, with the mechanisms being clarified. Various approaches to microstructural control of FIMCs are proposed and validated. Significant refinement of FIMCs has been achieved through inoculation of TiB2 particles that had been previously modified with deliberately interfacial segregation of desirable alloying elements, leading to the development of the novel “compositional templating” concept.
Magnesium oxide (MgO) films and particles have been collected by pressurised filtration of a Mg-8.6wt%Al-0.67wt%Zn (AZ91D) alloy melt. The morphology of the oxides and their interfaces with the α-Mg phase were investigated by high-resolution transmission electron microscopy. It was found that the oxide films consisted of large numbers of sub-micrometre-sized MgO particles, and that melt shearing can effectively break up the oxide films and disperse the oxide particles. For the first time, orientation relationships (ORs) of OR I: [1 1 1]MgO∼2° from (0 0 0 1)α-Mg and (0 1 1)MgO //[2 1 1 0)α-Mg; and OR II: (1 1 1)MgO//(1 1 0 1)α-Mg and [0 1 1]MgO//[1 2 1 1]α-Mg, were observed between the MgO particles and the α-Mg matrix. The calculated Bramfitt planar disregistries were 5.5% and 2.5% for the two ORs, respectively, indicating good lattice matching between MgO and α-Mg at the interface. With the evidence of grain refinement effect observed in the sheared AZ91D magnesium alloy, the possibility of MgO particles to act as potent nucleants for heterogeneous nucleation of α-Mg grains is discussed in terms of the crystallographic criterion.
Heterogeneous nucleation is a widespread phenomenon in both nature and technology. However, our current understanding is largely confined to the classical nucleation theory (CNT) postulated over a century ago, in which heterogeneous nucleation occurs stochastically to form a spherical cap facilitated by a substrate. In this paper, we show that heterogeneous nucleation in systems with negative lattice misfit completes deterministically within three atomic layers by structural templating to form a two-dimentional template from which the new phase can grow. Using molecular dynamics (MD) simulations of a generic system containing metallic liquid (Al) and a substrate of variable lattice misfit (fcc lattice with fixed Al atoms), we found that heterogeneous nucleation proceeds layer-by-layer: the first layer accommodates misfit through a partial edge dislocation network; the second layer twists an angle through a partial screw dislocation network to reduce lattice distortion; and the third layer creates a crystal plane of the solid (the 2D nucleus) that templates further growth. The twist angle of the solid relative to the substrate as a signature of heterogeneous nucleation in the systems with negative lattice misfit has been validated by high resolution transmission electron microscopic (HRTEM) examination of TiB2/Al and TiB2/α-Al15(Fe, Mn)3Si2 interfaces in two different Al-alloys.
This article provides an overview of high-pressure die casting (HPDC)-related research undertaken at the EPSRC Future LiME Hub between 2015–2022. The project aimed to identify the cause of variability in the tensile ductility of die-cast structures, and to develop novel processing techniques to address this issue. Variability in tensile ductility was related to the size of large pores and non-metallic inclusions. It was proposed that these non-metallic inclusions formed during the pyrolysis of commercial plunger lubricants in the shot sleeve, and that these large pores derived from dilatational strains introduced during semi-solid deformation. Processing parameters and die design were found to significantly influence the microstructure of die-cast products, and the subsequent variability in tensile ductility. To close, recent progress on the application of intensive melt shearing to HPDC is reviewed. Intensive melt shearing was found to induce significant grain refinement in both Al and Mg alloys due to the effective dispersion of native oxide particles, and the use of these particles as heterogeneous nucleation substrates. The presence of native oxide particles also enabled the use of novel heat treatment procedures that avoided conventional issues such as surface blistering and geometrical distortion.
During solidification of metallic materials, heterogeneous nucleation occurs on substrates, either endogenous or exogenous. The potency of the substrates for nucleation is mainly dependent upon the atomic arrangements on the substrate surface, which are affected by the lattice misfit between the substrate and the nucleated solid, the surface roughness at atomic scale, and the chemical interaction between the substrates and the melt. Extensive examinations on metal/substrate (M/S) interfaces at atomic scale by the state-of-the-art aberration (Cs) corrected STEM and associated EDS and EELS have shown that alloying elements in liquid melts tend to segregate at the interfaces, leading to the formation of various 2-dimensional compounds (2DCs) or 2-dimensional solutions (2DSs), depending upon segregation behavior of the elements. For instance, Al3Ti 2DC and Ti2Zr 2DC at the Al/TiB2 interface, Y2O3 2DC at the Mg/MgO interface, and a Si-rich 2DS layer at Al-Si/TiB2 interface have been identified. Such interfacial segregations significantly affect nucleation potency of the substrates, resulting in either promoting or impeding the heterogeneous nucleation process during solidification. In this paper, we present an overview of the current studies of interfacial segregation behavior, the structure and chemistry of interfaces, and their impacts on the subsequent heterogeneous nucleation and grain initiation processes. Our focus is on the advances made in the understanding of the mechanisms for nucleation and grain refinement. It is demonstrated that it is feasible to manipulate heterogeneous nucleation by modifying nucleation potency of a substrate through deliberate interfacial segregation of desirable elements, achieving effective control of the grain structure of cast metallic materials.