Water-based drilling fluids (WBDF) are often used over oil-based drilling fluids due to economic reasons and environmental regulations. Bentonite-free WBDF is preferred to aid in the reduction of formation damage. In many cases, this WBDF is formulated with xanthan gum. The performance of drilling operations is mainly affected by the drilling fluid formulation. The complex interactions among polymer concentration, thermal, and shear histories influence the rheological behavior of drilling fluids. The present study aims to analyze the effects of xanthan gum concentration on the rheological behavior of water-based drilling fluids. The experimental results performed in rotational rheometers revealed a relationship between concentration, yield stress, and thixotropic phenomena. The increase in xanthan gum concentration not only enhances the stability of the drilling fluid, allowing for more prolonged process interruptions without risking the fluid degradation but also improves the thermal stability of the sample. These findings show that the concentration of xanthan gum improves water-based drilling fluids' rheological and thermal stability.
The current work is devoted to analyzing viscoplastic fluid flow in a circular axisymmetric abrupt contraction with ratio . The velocity fields and static pressure along a hydraulic loop were measured employing Particle Image Velocimetry technique and a pressure transducers system, respectively. Four aqueous solutions of Carbopol 940 with different rheological parameters were used as viscoplastic fluids. Laminar and turbulent flow conditions are evaluated and compared with the generalized Hagen–Poiseuille law and the Malin friction factor correlations supported by turbulent fluctuations measurements. The formation of a plug core region is observed around the centerline of the pipe. The relationships between the velocity profiles and the shear stress distribution with the plug core were investigated supported via shear rate calculations. The results show that the yield stress highly influences the shape of the velocity profiles and the appearance of unyielded regions at the contraction edges. The shear stress maps show a layered distribution across the pipe diameter with higher values located at the contraction entrance. Instead, a constant shear stress distribution is found in the unyielded regions. The size of these unyielded regions increases with the yield stress but is reduced at regions with high shear rates due to increased inertial forces. Pressure drop measurements contrasted with the shear stress and velocity gradients maps illustrated that the pressure losses along the pipe are affected by the yield stress and the Reynolds number. However, a non-dependence of the pressure loss coefficient at the contraction plane with the rheological parameters is evidenced, as presented in earlier experimental results. This differs from many numerical studies since the contraction’s pressure loss coefficient for viscoplastic fluids is directly affected by the increase of inertial forces at this region.
This paper presents an experimental study of the flow of an elasto-viscoplastic fluid (Carbopol) in a rectangular duct with an abrupt contraction of an aspect ratio of 4:1. At the corners of the contraction, a dead zone appears with no recirculation zone. The hydrodynamics of the flow is studied using high-resolution laser Doppler velocimetry (LDV). We focus, in particular, on velocity and shear rate profiles within and above the dead zone. The position of the solid–liquid interface is provided for different flow rates. The velocity profiles show a line where they overlap at the same point, known as the “slip line.” The position of this line is independent of the flow rate, but its velocity evolves with the flow rate, for which we have proposed a correlation. The position of this line aligns with the level of contraction for all flow rates. Shear rate profiles show a non-monotonic evolution: from zero at the solid–liquid interface to a peak, then decreasing to zero again in the plug zone at the core of the pipe, indicating the presence of different layers between the solid–liquid interface and the slip line. The line of maximum shear rate is independent of the flow rate, suggesting that the width of the zone between the slip line and this line remains constant at all flow rates. The study is completed by establishing correlations between the friction factor (f) and the Euler number (Eu) as a function of the generalized Reynolds number Regen upstream, downstream, and at the level of contraction.
The present study examines the impact of slip in Carbopol solutions during the restart flow in pipelines utilizing in situ visualization techniques. Rheological tests were conducted using smooth and hatched parallel plate geometries to obtain the rheological characteristics of the solutions. The behavior of the solutions in the creep tests is compared with those in the experimental unit. Three flow regimes were identified through rheological and experimental setup tests: non-flow, slip, and yielded. The slip regime allowed the establishment of a slip static yield stress value, indicating significant deformation states, and a restart pressure decrease of about 61% when compared to the static yield stress. The flow dynamics under the wall slip effect is captured by velocity profiles, velocity contour maps and velocity gradient. Transient correlations of the scaling law type were determined, with wall slip in proportion to the velocity gradient and wall shear stress. Additionally, the concentration of viscoplastic material in the solution increased the scaling law index. This research seeks to provide valuable findings by quantifying the effects of apparent wall slip through in situ measurements. Such insights are crucial for designing and managing pipeline transport systems that handle yield stress fluids, applicable across various industries including cosmetics, food processing, and the production of waxy oils.
Drilling fluids are essential for maintaining cutting suspension during drilling, exhibiting gel-like behavior at rest and liquid-like behavior under shearing. These fluids display shear-thinning behavior, yield stress, and thixotropy. This study investigates the impact of aging time on stress overshoot and the deformation required to disrupt the gelled structure of water-based and synthetic-based drilling fluids. Flow start-up tests were conducted using a rotational rheometer at 25 °C and atmospheric pressure. The results show that aging time significantly affects both stress overshoot and the shear strain needed to disrupt the gelled structure. Longer aging times reduce the strain required to break the structure, indicating a correlation between aging time and stress overshoot. The fitted model strongly correlates with the experimental data, providing valuable insights for the planning and simulation of offshore drilling wells, primarily in well stability.