A design method for frequency selective surface (FSS) structure with high angular stability has been proposed in this paper. In the proposed method, bandwidth angular stability of FSS structure has been improved by adopting the bandwidth compensation technique and structural parameters can be obtained with a curve-fitting method from the desired resonate frequency and bandwidth. Discussions on improving the bandwidth design accuracy have been presented. By taking bandwidth angular stability into consideration, structure designed by the proposed method is more suitable to construct FSS radome. For verification, an FSS structure operating at 15 GHz with a bandwidth of 2 GHz has been designed, fabricated and measured. Good agreements between the simulated and measured results can be observed.
3 December 2019 in IEEE Transactions on Antennas and Propagation
In this paper, an equivalent circuit based design method for synthesizing second-order band-pass frequency selective surface (FSS) with the wide out-of-band rejection and fast roll-off characteristics has been proposed. To depict the desired frequency response, an equivalent circuit model is established. Then, according to the equivalent circuit model, a generalized composite structure composed of three FSS arrays separated by two dielectric substrates is proposed. The main advantage of this method is that it allows acquiring the optimized structural parameters according to the desired frequency response. With the design method, an FSS based on the proposed composite structure is designed. The designed FSS can provide a second-order pass-band within the stop-band ranging from 1GHz to 40GHz and the pass-band is operating at 10GHz with 12% fractional bandwidth. Meanwhile, the bandwidth of the two transitional bands on both sides of the pass-band is only 0.26GHz and 0.6GHz, respectively. Also, the frequency response of the designed FSS is stable at 60° for both TE and TM polarizations. For further verification, an FSS prototype is fabricated and experimentally characterized. Good agreements between the simulated and measured results can be observed.
10 January 2024 in IEEE Transactions on Antennas and Propagation
This article demonstrates a conformal miniaturized bandpass frequency selective surface (FSS) with excellent frequency response stability. First, the simulation design for the finite FSS array is proposed. Next, the central connection patch, the ring patch, and the aperture elements, mapped from the first-order equivalent circuit model (ECM), are chosen to obtain transmission properties under conformal conditions. The influence law of elements on the performance stability and elements suitable for narrowband or wideband under conformal conditions are summarized. Based on these, a miniaturized wideband FSS for X-band with stable transmission performance is designed. The angular stability of the planar FSS can reach 75°. In the case of the conformal FSS with the bending angle of 5π/6, the resonance frequency deviation is 2.32% under y-polarized and almost zero under x-polarized. The transmission coefficients of the FSS prototype are also measured for both planar and curved surfaces. When the FSS is conformal on the cylindrical surface with a radius of 159 mm, the resonance frequency deviation can be almost negligible, and the transmission performance remains stable up to 70°. The measurement results are in good agreement with the simulation results, verifying the effectiveness of the proposed FSS structure and the simulation design.
17 May 2023 in IEEE Antennas and Wireless Propagation Letters
In this letter, a design method for frequency selective surface (FSS) based on the equivalent circuit model (ECM) and deep learning is proposed. In the proposed method, the ECM depicting the target transmission characteristic is first established. Then, with the aid of the established ECM, the target transmission characteristic is converted into the desired transmission curve and the initial topology of the FSS structure is determined. The cascade network is adopted to realize the rapid inverse design of the FSS structure. Benefiting from the established ECM, the high quality of the training data and proper description of the design target can be ensured in deep learning. For verification, an ultra-wideband FSS structure with a passband ranging from 3.1 to 12.05GHz and a stopband ranging from 12.85 to 20GHz is designed. Both simulated and experimental results show that the designed FSS provides an ultra-wide passband with flat-top and fast roll-off characteristics, covering 98.9% target passband and 95.3% target stopband.
In this paper, a nonlinear PID (NLPID) controller is used to replace a traditional PID controller to overcome the influence of nonlinear factors in the computer numerical control (CNC) system. A particle swarm optimization based on a generalized opposition-based learning (G-PSO) algorithm is proposed to optimize the NLPID controller. The convergence speed and global optimization ability of the particle swarm optimization (PSO) algorithm are improved by introducing generalized opposition-based learning. The natural selection mutation is introduced into the G-PSO algorithm to further avoid the particles falling into local optimization. Different from the existing research, this paper designs a special fitness function according to the control objectives of improving system response speed and suppressing overshoot. By comparing the differential evolution (DE) algorithm, the ant lion optimizer (ALO) and the genetic algorithm (GA) through simulation, it is proven that the G-PSO algorithm has a faster convergence speed and better global optimization ability. Compared to Fuzzy PID and MRAC PID, G-PSO NLPID is shown to be more suitable for CNC systems. Additionally, it is proven through experiments that the rise time and settling time of the NLPID controller optimized by the G-PSO algorithm are 22.22% and 24.52% faster, respectively, than the traditional PID controller, and the system overshoot is successfully suppressed.
17 December 2019 in Journal of Physics D: Applied Physics
This paper presents a high-frequency transmissive frequency selective rasorber (FSR) with wideband transmission/ absorption properties. It is synthesized by placing a resistive sheet on top of a bandpass frequency selective surface (FSS) separated by an air spacer. The unit cell of resistive sheet comprises the resistor-loaded central tortuous Jerusalem cross. Its central tortuous cross, acting as a parallel LC resonator with a high inductance and a low capacitance, is utilized to realize a wide pass-band with low insertion loss by cutting off resistive sheet’s lossy path over a wide frequency band. The bandpass FSS adopts a triple-layer coupled structure, in which two layers of identical capacitive metallic patches are coupled through an intermediate inductive wire grid. A second-order pass-band with high selectivity is realized by this bandpass FSS. Simulation results show that the fractional bandwidth of the 1 dB transmission band and the 10 dB absorption band is 19.6% and 107.9%, respectively. Meanwhile, since its periodicity is only 8 mm, the proposed FSR also shows good angular and polarization stabilities. A good agreement between the measured and simulated results validates the proposed FSR design.