Improving the energy density of Li-ion batteries is critical to meet the requirements of electric vehicles and energy storage systems. In this work, LiFePO4 active material was combined with single-walled carbon nanotubes as the conductive additive to develop high-energy-density cathodes for rechargeable Li-ion batteries. The effect of the morphology of the active material particles on the cathodes’ electrochemical characteristics was investigated. Although providing higher packing density of electrodes, spherical LiFePO4 microparticles had poorer contact with an aluminum current collector and showed lower rate capability than plate-shaped LiFePO4 nanoparticles. A carbon-coated current collector helped enhance the interfacial contact with spherical LiFePO4 particles and was instrumental in combining high electrode packing density (1.8 g cm−3) with excellent rate capability (100 mAh g−1 at 10C). The weight percentages of carbon nanotubes and polyvinylidene fluoride binder in the electrodes were optimized for electrical conductivity, rate capability, adhesion strength, and cyclic stability. The electrodes that were formulated with 0.25 wt.% of carbon nanotubes and 1.75 wt.% of the binder demonstrated the best overall performance. The optimized electrode composition was used to formulate thick free-standing electrodes with high energy and power densities, achieving the areal capacity of 5.9 mAh cm−2 at 1C rate.
A novel polyaniline-modified CNT and graphene-based nanocomposite (2.32–7.34 nm) was prepared and characterized by spectroscopic methods. The specific surface area was 176 m2/g with 0.232 cm3/g as the specific pore volume. The nanocomposite was used to remove zinc and lead metal ions from water; showing a high removal capacity of 346 and 581 mg/g at pH 6.5. The data followed pseudo-second-order, intraparticle diffusion and Elovich models. Besides this, the experimental values obeyed Langmuir and Temkin isotherms. The results confirmed that the removal of lead and zinc ions occurred in a mixed mode, that is, diffusion absorption and ion exchange between the heterogeneous surface of the sorbent containing active adsorption centers and the solution containing metal ions. The enthalpy values were 149.9 and 158.6 J.mol−1K−1 for zinc and lead metal ions. The negative values of free energies were in the range of −4.97 to −26.3 kJ/mol. These values indicated an endothermic spontaneous removal of metal ions from water. The reported method is useful to remove the zinc and lead metal ions in any water body due to the high removal capacity of nanocomposite at natural pH of 6.5. Moreover, a low dose of 0.005 g per 30 mL made this method economical. Furthermore, a low contact time of 15 min made this method applicable to the removal of the reported metal ions from water in a short time. Briefly, the reported method is highly economical, nature-friendly and fast and can be used to remove the reported metal ions from any water resource.
The characteristics of lithium iron phosphate cathodes containing various types of commercially available carbon nanotubes—single-walled (SWCNTs), double-walled (DWCNTs), and multi-walled (MWCNTs)—have been compared. Electrochemical characteristics of the cathode materials have been studied by electrochemical impedance spectroscopy and galvanostatic charge/discharge measurements. The cyclic stability at various current densities has been estimated. The best electrochemical characteristics are shown by the cathode materials containing SWCNTs (advantage over the DWCNT-based cathode materials at discharge rates higher than 10C) and DWCNTs (advantage over the SWCNT-based cathode materials during long-term cycling). During the long-term cycling at a current density of 1C, the greatest loss of capacity is observed for the MWCNT-based electrode. At the same time, the SWCNT- and DWCNT-based electrodes demonstrate satisfactory capacity retention after 50 charge/discharge cycles: over 94 and 98%, respectively.
1 March 2020 in Inorganic Materials: Applied Research
The synthesis of a nanocomposite material based on graphene modified with iron oxide nanoparticles, which is an effective sorbent of organic pollutants contained in aqueous media, has been considered. The production of graphene by chemical reduction of graphene oxide (GO) is the most flexible and popular method for the synthesis of composite materials of various structures based on graphene. Chemical reduction of graphene oxide was carried out using gamma-lactone-2,3-dehydro-L-gulonic acid (ascorbic acid). The method of obtaining the composite under study includes processing the hydrogel obtained after the GO reduction in supercritical isopropanol, which makes it possible to obtain graphene aerogel containing nanoparticles of iron(II, III) oxide. The analysis of the specific surface and porosity of the obtained aerogel showed that the specific surface area of the aerogel was ~7 times higher as compared to the specific surface of the xerogel obtained by drying of the hydrogel under ordinary conditions in air. The diffractometric analysis of xerogel and aerogel samples suggests that, during supercritical drying in the organic fluid, the processes of iron hydroxide reduction to iron(II, III) oxide proceed. The sorption capacity of the obtained hydro- and aerogel was studied by the extraction of methylene blue organic dye from aqueous solutions in a static mode (batch method). The results of the experiments showed that the maximum values of the sorption capacity for the methylene blue dye were 1370 and 1326 mg/g for the hydro- and aerogel, respectively.