The nickel-based superalloy, Haynes 230 (H230), is widely used in high-temperature applications, e.g., heat exchangers, because of its excellent high-temperature mechanical properties and corrosion resistance. As of today, H230 is not yet in common use for 3D printing, i.e., metal additive manufacturing (AM), primarily because of its hot cracking tendency under fast solidification. The ability to additively fabricate components in H230 attracts many applications that require the additional advantages leveraged by adopting AM, e.g., higher design complexity and faster prototyping. In this study, we fabricated nearly fully dense H230 in a laser powder bed fusion (L-PBF) process through parameter optimization. The efforts revealed the optimal process space which could guide future fabrication of H230 in various metal powder bed fusion processes. The metallurgical analysis identified the cracking problem, which was resolved by increasing the pre-heat temperature from 80 °C to 200 °C. A finite element simulation suggested that the pre-heat temperature has limited impacts on the maximum stress experienced by each location during solidification. Additionally, the crack morphology and the microstructural features imply that solidification and liquation cracking are the more probable mechanisms. Both the room temperature tensile test and the creep tests under two conditions, (a) 760 °C and 100 MPa and (b) 816 °C and 121 MPa, confirmed that the AM H230 has properties comparable to its wrought counterpart. The fractography showed that the heat treatment (anneal at 1200 °C for 2 h, followed by water quench) balances the strength and the ductility, while the printing defects did not appreciably accelerate part failure.
23 August 2023 in Journal of Solar Energy Engineering
Design of an additively manufactured molten salt (MS) to supercritical carbon dioxide (sCO2) primary heat exchanger (PHE) for solar thermal power generation is presented. The PHE is designed to handle temperatures up to 720 °C on the MS side and an internal pressure of 200 bar on the sCO2 side. In the core, MS flows through a three-dimensional periodic lattice network, while sCO2 flows within pin arrays. The design includes integrated sCO2 headers located within the MS flow, allowing for a counter flow design of the PHE. The sCO2 headers are configured to enable uniform flow distribution into each sCO2 plate while withstanding an internal pressure of 200 bar and minimizing obstruction to the flow of MS around it. The structural integrity of the design is verified on AM 316 stainless steel printed sub-scale specimens. An experimentally-validated, correlation-based sectional PHE core thermofluidic model is developed to study the impact of flow and geometrical parameters on the PHE performance, with varied parameters including the mass flow rate, surface roughness, and PHE dimensions. A process-based cost model is used to determine the impact of parameter variation on build cost. The model results show that a heat exchanger with a power density of 18.6 MW/m3 (including sCO2 header volume) and effectiveness of 0.88 can be achieved at a heat capacity rate ratio of 0.8. The impact of design and AM machine parameters on the cost of the PHE are assessed.
20 January 2025 in Integrating Materials and Manufacturing Innovation
Grain size distribution is a critical factor in determining materials’ physical and mechanical properties, including thermal conductivity, hardness, and creep behavior. Understanding the distribution of grain sizes is essential for advancing the comprehension of material properties and improving materials development and design. Traditional methods for determining grain size, such as electron backscatter diffraction (EBSD), are resource-intensive, underscoring the need for more efficient approaches to grain segmentation in standard micrographs, such as those obtained via SEM and optical imaging. This paper presents a streamlined, unsupervised computer vision pipeline that employs superpixel segmentation and region adjacency merging techniques to segment and measure grain geometry from micrographs efficiently. The pipeline is validated using two methods: hand-labeled SEM images of laser powder bed fusion (LPBF) fabricated Haynes 282 Ni-alloy and open-source EBSD data of IN100 from Dream3D. Both validation approaches achieved IoU and Dice scores greater than 0.9, while processing an image with a resolution of 1000 × 1000 pixels in under 40 s, demonstrating a fast and sufficiently accurate pipeline.
30 July 2026 in International Journal of Heat and Mass Transfer