The use of image processing for the detection and classification of defects has been a reality for some time in science and industry. New methods are continually being presented to improve every aspect of this process. However, these new approaches are applied to a small, private collection of images, which makes a real comparative study of these methods very difficult. The objective of this paper was to compile a public annotated benchmark, that is, an extensive set of images with and without defects, and make these public, to enable the direct comparison of detection and classification methods. Moreover, different methods are reviewed and one of these is applied to the set of images; the results of which are also presented in this paper.

A growing number of industrial applications incorporate multimedia information processing. These multimedia applications are commonly distributed and subject to time constraints that must be met across networks without creating intolerable interference over typical control flows. However, multimedia traffic, in general, and video streaming, in particular, have specific characteristics that conflict with the operational framework of conventional real-time protocols. In particular, video compressors generate highly variable bit-rate streams that mismatch the constant-bit-rate channels typically provided by real-time protocols, severely reducing the efficiency of network utilization. This paper focuses on low-latency multimedia transmission over Ethernet with dynamic quality-of-service (QoS) management. We propose a multidimensional mechanism that controls, in an integrated way, both the compression parameters and the network bandwidth allocated to each stream. The goal is to provide the best possible QoS to each stream, recomputing the compression levels and network bandwidth whenever significant events, such as channel setup/teardown, or structural changes happen. This paper also presents novel QoS metrics based both on the image quality and network parameters. Several experiments with prerecorded video streams illustrate the advantages of the proposed approach and the convenience of the metrics.

The growing use of mobile nodes in manufacturing environments is increasing the Quality of Service (QoS) requirements of the communications infrastructures that support them, as is the case with Industrial Wireless Sensor Networks (IWSN). Managing networks using Software Defined Networks (SDN) addresses the challenge of handling multiple sources in a satisfactory manner. The global vision of the topology that the SDN controller has allows a logical segmentation of the network, through the allocation of dedicated resources for each information flow, thus ensuring independent service levels and complete isolation. Mobile nodes produce constant changes in topology, which lead to instability for routing protocols. Traditional routing solutions with protocols such as Routing Protocol for Low-Power and Lossy Networks (RPL) require additional time to make the parent node change. This paper proposes Mobile Multicast Forwarding with Software Defined Network (MMF-SDN), an approach using Software Defined Networking solution for WIreless SEnsor Network (SDN WISE) protocol that exploits the advantages of SDN and Time Slotted Channel Hopping (TSCH) synchronism. The mobile nodes are managed as multicast sources, through a cumulative allocation of resources from the controller. This allows reception states to be synchronized at the parent nodes to provide network stability, avoiding subsequent recalculations in the routing protocol. Parent node changes are transparent and immediate. This proposal improves on other SDN based solutions, reducing energy consumption in reception by up to 50%, 70% end-to-end delay and improving scalability with a 30% reduction in slotframe occupancy.

Wireless Sensor Networks have become a key enabler for Industrial Internet of Things (IoT) applications; however, to adapt to the derived robust communication requirements, deterministic and scheduled medium access should be used, along with other features, such as channel hopping and frequency diversity. Implementing these mechanisms requires a correct synchronization of all devices in the network, a stage in deployment that can lead to non-operational networks. The present article presents an analysis of such situations and possible solutions, including the common current approaches and recommendations, and proposes a new beacon advertising method based on a specific Trickle Timer for the Medium Access Control (MAC) Time-Slotted Channel Hopping (TSCH) layer, decoupling from the timers in the network and routing layers. With this solution, improvements in connection success, time to join, and energy consumption can be obtained for the widely extended IEEE802.15.4e standard.

IWSNs (Industrial Wireless Sensor Networks) have become the next step in the evolution of WSN (Wireless Sensor Networks) due to the nature and demands of modern industry. With this type of network, flexible and scalable architectures can be created that simultaneously support traffic sources with different characteristics. Due to the great diversity of application scenarios, there is a need to implement additional capabilities that can guarantee an adequate level of reliability and that can adapt to the dynamic behavior of the applications in use. The use of SDNs (Software Defined Networks) extends the possibilities of control over the network and enables its deployment at an industrial level. The signaling traffic exchanged between nodes and controller is heavy and must occupy the same channel as the data traffic. This difficulty can be overcome with the segmentation of the traffic into flows, and correct scheduling at the MAC (Medium Access Control) level, known as slices. This article proposes the integration in the SDN controller of a traffic manager, a routing process in charge of assigning different routes according to the different flows, as well as the introduction of the Time Slotted Channel Hopping (TSCH) Scheduler. In addition, the TSCH (Time Slotted Channel Hopping) is incorporated in the SDN-WISE framework (Software Defined Networking solution for Wireless Sensor Networks), and this protocol has been modified to send the TSCH schedule. These elements are jointly responsible for scheduling and segmenting the traffic that will be sent to the nodes through a single packet from the controller and its performance has been evaluated through simulation and a testbed. The results obtained show how flexibility, adaptability, and determinism increase thanks to the joint use of the routing process and the TSCH Scheduler, which makes it possible to create a slicing by flows, which have different quality of service requirements. This in turn helps guarantee their QoS characteristics, increase the PDR (Packet Delivery Ratio) for the flow with the highest priority, maintain the DMR (Deadline Miss Ratio), and increase the network lifetime.