Temporary plugging diversion fracturing (TPDF) technology has been widely used in various oil fields for repeated reconstruction of high-water-cut old oil wells and horizontal well reservoir reconstruction. Previous studies have carried out in-depth study on the pressure-bearing law and placement morphology of different types of temporary plugging agents (TPAs) in fractures, but there are relatively few studies on TPA accumulation body permeability. To solve this problem, an experimental device for evaluating the TPA performance with adjustable fracture pores is proposed in this paper. Based on the test of fracturing fluid breaking time and residue content, the low damage of fracturing fluid to the reservoir is determined. The TPA degradation performance test determines whether the TPA causes damage to the hydraulic fracture after the temporary plugging fracturing. Finally, by testing the TPA pressure-bearing capacity and the temporary plugging aggregation body permeability, the plugging performance and the aggregation body permeability are determined. The results show the following: (1) Guar gum fracturing fluid shows good gel-breaking performance under the action of breaking agent, and the recommended concentration of breaking agent is 300 ppm. At 90~120 °C, the degradation rate of the three types of TPAs can reach more than 65%, and it can be effectively carried into the wellbore during the fracturing fluid flowback stage to achieve the effect of removing the TPA in the fracture. (2) The results of the pressure-bearing performance of the TPA show that the two kinds of TPAs can quickly achieve the plugging effect after plugging start: the effect of ZD-2 (poly lactic-co-glycolic acid (PLGA)) particle-and-powder combined TPA on forming an effective temporary plugging accumulation body in fractures is better than that of ZD-1 (PLGA) pure powder. There are large pores between the particles, and the fracturing fluid can still flow through the pores, so the ZD-3 (a mixture of lactide and PLGA) granular temporary plugging agent cannot form an effective plugging. (3) The law of length of the temporary plugging accumulation body shows that the ZD-2 combined TPA has stronger plugging ability for medium-aperture simulated fracture pores, while the ZD-1 powder TPA has stronger plugging ability for small aperture simulated fracture pores, and the ZD-3 granular TPA should be avoided alone as far as possible. This study further enriches and improves the understanding of the mechanism of temporary plugging diverting fracturing fluid.

A temporary plugging agent is an effective tool for increasing production in old wells. By considering the temporary plugging materials used in the remote WY area, three concentrations and five ratios under different fracture widths were designed and optimized. Thus, the fracture diversion under true triaxial stress was studied. The results showed that when the fracture widths were 2.0, 4.0, and 6.0 mm, the corresponding optimal plugging scheme was that the concentrations of the temporary plugging agent were 12.0, 18.0, and 18.0 kg/m³ and the ratios of 20–70 mesh to 200–300 mesh temporary plugging agent were 4:1, 2:1 and 4:1, respectively. When maintaining the same horizontal stress, an increase in the axial stress was accompanied by an increase in the fracture pressure; the initial fractures almost propagated along the direction of the horizontal maximum principal stress, but the shapes of the turning fractures were different. When the axial stress was the same, an increase in the horizontal stress difference was accompanied by a decrease in the corresponding fracture pressure and a gradual decrease in the degree of fracture turning. This study provides a basis for numerical simulation and field application of temporary plugging fracturing at fracture ends.

The homogeneous acid etching of conventional acid in porous heterogeneous carbonate reservoirs leads to a large amount of consumption in the near-wellbore area, which makes the acidification effect often not ideal. In order to improve the acidizing effect of porous heterogeneous carbonate reservoirs, viscous acid is used to increase the stimulation of the target block in this paper. Through systematic experiments, the adaptability of the viscous acid in the four layers of the M reservoir in the target block was evaluated, and the MD and ME layers suitable for acidizing stimulation were determined in combination with physical property analysis. Finally, based on the geological characteristics and experimental data of the preferred layers, a two-scale acid wormhole growth radial model was established, and the construction parameters of acidizing stimulation were optimized. The results show that (1) The preferred viscous acid system has a dissolution rate of more than 95% for the rock powder in the four layers. When the matrix permeability is high, the effect of the acid wormhole is obvious and the permeability increase is higher. (2) The steel sheet corrosion and residual acid damage experiments showed that the acid system was not corrosive to the wellbore, and the reservoir damage rate of the residual acid after the reaction was low. (3) Based on the relationship between reservoir porosity and permeability and the position of edge and bottom water, the MD and ME layers with more potential for acidizing stimulation are selected. (4) The results of the numerical simulation show that the optimal acid pump rate of the MD and ME layers is 1.4 bpm and 1.0 bpm, and the acidizing fluid volume is 255 bbl, which can form effective acid wormholes, and the range of reservoir permeability transformation is the largest. The field application results show that the optimization scheme effectively improves the production of oil wells, verifies the practicability of the scheme, and provides a reference for the process optimization of viscous acid in the same type of porous heterogeneous carbonate reservoir stimulation.

Mishrif (M) reservoir of Faihaa (F) oilfield in Iraq is a heterogeneous porous carbonate reservoir. The reservoir properties of each reservoir unit differ greatly, and the distribution of porosity and permeability is non-uniform. Some reservoir units have the problem that the expected production cannot be achieved or the production decline rate is too fast after matrix acidification. This work optimized and compared the process of acid fracturing and hydraulic fracturing techniques. The Mishrif B (MB) and Mishrif C (MC) layers are selected as the target units for fracturing and the perforation intervals are optimized. The acid fracturing process adopted the acid fracturing technology of guar gum pad fluid and gelled acid multi-stage injection. According to the wellhead pressure limit and fracture propagation geometry, the pumping rate is optimized. The recommended maximum pumping rate of acid fracturing is 5.0 m³/min, and the optimized acid volume is 256.4 m³. The pressure changes during hydraulic fracturing and acid fracturing are different. It is recommended that the maximum hydraulic fracturing pump rate is 4.5 m³/min for MB and MC layers, and the amount of proppant in MB and MC layers is 37.5 m³ and 43.7 m³, respectively. The production prediction of two optimized processes is carried out. The results showed that the effect of acid fracturing in MB and MC layers is better than hydraulic fracturing, and it is recommended to adopt acid fracturing technology to stimulate MB and MC layers. Acid fracturing operation is carried out in the X-13 well, and better application results are achieved. The results of this study provide optimized reference ideas for reservoir stimulation in heterogeneous porous reservoirs.

The development of natural fractures (NFs) in shale gas reservoirs is conducive to improving the productivity of shale gas wells. However, NF development leads to high-frequency frac hits between the infill and parent wells, which critically restricts its efficiency. To elucidate the large contribution of hydraulic fractures (HFs) and NFs in frac hits during the production and the development of NF-developed shale gas reservoirs, such reservoirs in the WY area of western China are taken as an example. A total of 197 frac hits well events in this area are systematically classified via the frac-hit discrimination method, and the effects of different factors on HF- and NF- dominated frac hits are classified and studied. Combined with the correlation analysis method and the chart method, the main controlling factors affecting the two types of frac hits are determined, and the corresponding frac-hit prevention countermeasures are proposed. The research demonstrates that (1) the distribution and development of NFs are crucial to production after frac hits. NFs and HFs in the WY area cause 51% and 49%, respectively, of the frac hits. (2) The main controlling factors in NF-dominated frac hits are the approximation angle, fracture linear density, and horizontal stress difference, whereas they are net pressure in fractures, horizontal stress difference, and liquid strength in HF-dominated frac hits. Sensitivity analysis shows that the NF activation difficulty coefficient fluctuates between −35.1% and 47.6%, and the maximum hydraulic fracture length fluctuates between −43.5% and 25.29%. (3) The corresponding frac-hit prevention countermeasures are proposed for the two types of formation mechanisms from different approaches, including frac-hit risk assessment and path planning, production well pressurization and stress diversion, and infill-well fracturing parameter optimization. This paper not only provides a reference for exploring the formation mechanism of frac hits in fractured shale gas reservoirs but also a theoretical basis for the corresponding frac-hit prevention countermeasures.

After long-term water injection development in Block M of the Gudong Oilfield, the fluid seepage field in the formation has become increasingly complex, and the heterogeneity of the reservoir has intensified. The uneven injection-production and the differences in lithological permeability have further led to a series of problems such as uneven reserve utilization, a low injection-production correspondence rate, and a poor overall development effect. During the development process, severe water flooding at the bottom and rich remaining oil at the top within the layer also emerged. These issues not only affected the economic benefits of the oilfield but also put forward higher requirements for the subsequent development strategies. In order to solve the above problems, based on a detailed analysis of geological characteristics, reservoir engineering and monitoring data, this paper uses the numerical simulation method to systematically simulate the dynamic changes in the residual oil saturation and pressure field in the formation under different development stages. The simulation results show that the pressure and saturation in each layer are both on a downward trend, especially in the layers with large pressure changes, where the oil saturation changes are more significant. Therefore, combined with the results of numerical simulation, a series of profile control and water shutoff schemes were systematically designed. These schemes covered different types of profile control agents and technological parameters. Representative well groups were selected to predict and evaluate the profile control effect. In the technical and economic evaluation of the profile control effect, the input–output ratio method was adopted. Finally, an optimal scheme was selected and applied in the field. The results show that after the implementation of this scheme, the daily oil increment of the well group was remarkable. During the test period, the cumulative oil increment reached 100 t, and the total expected oil increment could reach 190 t. The input–output ratio reached 1:2.1. The profile control measures significantly improved the injection-production correspondence, slowed down the in-layer water flooding, and further enhanced the recovery rate of remaining oil. In conclusion, the methods and achievements of this study can provide important technical references and support for the efficient and long-term development of similar high-water-cut and heterogeneous complex oil reservoirs, and have guiding significance for the subsequent adjustment, potential tapping, stable production and efficiency improvement of oilfields.