Yageng Li

Dr. Yageng Li

Department of Materials Science and Engineering, University of Science and Technology Beijing, Beijing, China

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2018 in Acta Biomaterialia
Verified
Journal Article
Closed access
Yageng LiYageng Li
Yageng Li
Jie ZhouJie Zhou
Jie Zhou
PPP. Pavanram
P. Pavanram
MLM.A. Leeflang
M.A. Leeflang
LFL.I. Fockaert
L.I. Fockaert
Amir A ZadpoorAmir A Zadpoor
Amir A Zadpoor

1 September 2018 in Acta Biomaterialia
Verified
Journal Article
Closed access
Yageng LiYageng Li
Yageng Li
Holger JahrHolger Jahr
Holger Jahr
KLK. Lietaert
K. Lietaert
PPP. Pavanram
P. Pavanram
AYA. Yilmaz
A. Yilmaz
Amir A ZadpoorAmir A Zadpoor
Amir A Zadpoor

1 January 2018 in Acta Biomaterialia
Verified
Journal Article
Open access
SAS.M. Ahmadi
S.M. Ahmadi
Reza HedayatiReza Hedayati
Reza Hedayati
Yageng LiYageng Li
Yageng Li
KLK. Lietaert
K. Lietaert
NTN. Tümer
N. Tümer
Amir A ZadpoorAmir A Zadpoor
Amir A Zadpoor
Additive manufacturing (AM) techniques enable fabrication of bone-mimicking meta-biomaterials with unprecedented combinations of topological, mechanical, and mass transport properties. The mechanical performance of AM meta-biomaterials is a direct function of their topological design. It is, however, not clear to what extent the material type is important in determining the fatigue behavior of such biomaterials. We therefore aimed to determine the isolated and modulated effects of topological design and material type on the fatigue response of metallic meta-biomaterials fabricated with selective laser melting. Towards that end, we designed and additively manufactured Co-Cr meta-biomaterials with three types of repeating unit cells and three to four porosities per type of repeating unit cell. The AM meta-biomaterials were then mechanically tested to obtain their normalized S-N curves. The obtained S-N curves of Co-Cr meta-biomaterials were compared to those of meta-biomaterials with same topological designs but made from other materials, i.e. Ti-6Al-4V, tantalum, and pure titanium, available from our previous studies. We found the material type to be far more important than the topological design in determining the normalized fatigue strength of our AM metallic meta-biomaterials. This is the opposite of what we have found for the quasi-static mechanical properties of the same meta-biomaterials. The effects of material type, manufacturing imperfections, and topological design were different in the high and low cycle fatigue regions. That is likely because the cyclic response of meta-biomaterials depends not only on the static and fatigue strengths of the bulk material but also on other factors that may include strut roughness, distribution of the micro-pores created inside the struts during the AM process, and plasticity. Meta-biomaterials are a special class of metamaterials with unusual or unprecedented combinations of mechanical, physical (e.g. mass transport), and biological properties. Topologically complex and additively manufactured meta-biomaterials have been shown to improve bone regeneration and osseointegration. The mechanical properties of such biomaterials are directly related to their topological design and material type. However, previous studies of such biomaterials have largely neglected the effects of material type, instead focusing on topological design. We show here that neglecting the effects of material type is unjustified. We studied the isolated and combined effects of topological design and material type on the normalized S-N curves of metallic bone-mimicking biomaterials and found them to be more strongly dependent on the material type than topological design.

1 October 2020 in Acta Biomaterialia
Verified
Journal Article
Open access
Yageng LiYageng Li
Yageng Li
Holger JahrHolger Jahr
Holger Jahr
Jie ZhouJie Zhou
Jie Zhou
AZAmir Abbas Zadpoor
Amir Abbas Zadpoor
Partially due to the unavailability of ideal bone substitutes, the treatment of large bony defects remains one of the most important challenges of orthopedic surgery. Additively manufactured (AM) biodegradable porous metals that have emerged since 2018 provide unprecedented opportunities for fulfilling the requirements of an ideal bone implant. First, the multi-scale geometry of these implants can be customized to mimic the human bone in terms of both micro-architecture and mechanical properties. Second, a porous structure with interconnected pores possesses a large surface area, which is favorable for the adhesion and proliferation of cells and, thus, bony ingrowth. Finally, the freeform geometrical design of such biomaterials could be exploited to adjust their biodegradation behavior so as to maintain the structural integrity of the implant during the healing process while ensuring that the implant disappears afterwards, paving the way for full bone regeneration. While the AM biodegradable porous metals that have been studied so far have shown many unique properties as compared to their solid counterparts, the unprecedented degree of flexibility in their geometrical design has not yet been fully exploited to optimize their properties and performance. In order to develop the ideal bone implants, it is important to take advantage of the full potential of AM biodegradable porous metals through detailed and systematic study on their biodegradation behavior, mechanical properties, biocompatibility, and bone regeneration performance. This review paper presents the state of the art in AM biodegradable porous metals and is focused on the effects of material type, processing, geometrical design, and post-AM treatments on the mechanical properties, biodegradation behavior, in vitro biocompatibility, and in vivo bone regeneration performance of AM porous Mg, Fe, and Zn as well as their alloys. We also identify a number of knowledge gaps and the challenges encountered in adopting AM biodegradable porous metals for orthopedic applications and suggest some promising areas for future research.

1 September 2019 in Acta Biomaterialia
Verified
Journal Article
Closed access
Yageng LiYageng Li
Yageng Li
HJH. Jahr
H. Jahr
PPP. Pavanram
P. Pavanram
FBF.S.L. Bobbert
F.S.L. Bobbert
UPU. Puggi
U. Puggi
Amir A ZadpoorAmir A Zadpoor
Amir A Zadpoor

1 March 2018 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
Reza HedayatiReza Hedayati
Reza Hedayati
SAS.M. Ahmadi
S.M. Ahmadi
KLK. Lietaert
K. Lietaert
BPB. Pouran
B. Pouran
Yageng LiYageng Li
Yageng Li
Amir A ZadpoorAmir A Zadpoor
Amir A Zadpoor