Oluwole Daniel Adigun

Mr. Oluwole Daniel Adigun

Federal University Oye Ekiti, Ikole-Ekiti, Nigeria
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 October 2022 in Ceramics
Verified
Journal Article
Open access
PDF file
OAOluwole Daniel Adigun
Oluwole Daniel Adigun
EREmmanuel III Ricohermoso
Emmanuel III Ricohermoso
ADAyodele Abeeb Daniyan
Ayodele Abeeb Daniyan
LULasisi Ejibunu Umoru
Lasisi Ejibunu Umoru
Emanuel IonescuEmanuel Ionescu
Emanuel Ionescu
This article reports on the structure and electronic properties of carbon-rich polysilazane polymer-derived silicon carbonitride (C/SiCN) corresponding to pyrolysis temperatures between 1100 and 1600 °C in an argon atmosphere. Raman spectroscopy, X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), Scanning Electron Microscopy (SEM) and Hall measurements were used to support the structural and electronic properties characterization of the prepared C/SiCN nanocomposites. A structural analysis using Raman spectroscopy showed the evolution of sp2 hybridized carbon phase that resulted from the growth in the lateral crystallite size (La), average continuous graphene length including tortuosity (Leq) and inter-defects distance (LD) with an increase in pyrolysis temperature. The prepared C/SiCN monoliths showed a record high room temperature (RT) electrical conductivity of 9.6 S/cm for the sample prepared at 1600 °C. The electronic properties of the nanocomposites determined using Hall measurement revealed an anomalous change in the predominant charge carriers from n-type in the samples pyrolyzed at 1100 °C to predominantly p-type in the samples prepared at 1400 and 1600 °C. According to this outcome, tailor-made carbon-rich SiCN polymer-derived ceramics could be developed to produce n-type and p-type semiconductors for development of the next generation of electronic systems for applications in extreme temperature environments.

7 September 2019 in FUOYE Journal of Engineering and Technology
Verified
Journal Article
Open access
PDF file
OAOluwole Daniel Adigun
Oluwole Daniel Adigun
SKSunday Kayode
Sunday Kayode
The concentration of inorganic chemical substances released into surface water from Okaba coal deposit were measured using spectroscopic techniques in order to assess the extent of pollution. Parameters measured (Pb, Fe, Cu, Cr, SO42-, Cl-, Mn, Zn and pH) showed that water samples within the mine area contain Pb, Fe, Cr, Cl-, Mn and Zn in concentrations beyond permissible intake limits; and the concentration of chloride measured (3000 mg/L) is capable of causing acid mine drainage (AMD). Concurrent evaluation of these inorganic substances using quantitative assessment reveal the possible presence of trace minerals like galena, sphalerite, chalcopyrite, pyrite and clay in Okaba coal deposit. Keywords— Acid mine drainage (AMD), Coal, Trace minerals, Water pollution

12 October 2023 in Journal of the Nigerian Society of Physical Sciences
Verified
Journal Article
Open access
PDF file
OAOluwole Daniel Adigun
Oluwole Daniel Adigun
LULasisi Egibunu Umoru
Lasisi Egibunu Umoru
TITemidayo Nancy Iwatan
Temidayo Nancy Iwatan
The most suitable electrolyte for graphene oxide synthesis, in terms of both production efficiency and quality, using the electrochemical exfoliation technique has been investigated and reported in this study. Simultaneous anodic and cathodic graphene oxide production using ten (10) different electrolytes, including acids (H2SO4, HCl, HNO3), bases (KOH, Ca(OH)2, Mg(OH)2, NaOH), and salts (NaCl, (NH4)2SO4, K2SO4), was studied under the same experimental conditions of bias voltage, graphite nature, exfoliation time, electrolyte molarity, and post-exfoliation treatments. Assessment of the graphene oxide structures and production rates was supported using Raman spectroscopy, high-resolution scanning electron microscopy (HRSEM), and EDS (energy dispersive x-ray spectroscopy), attached to the scanning electron microscope. Analysis of the results obtained reveals that H2SO4 showed the highest graphene oxide yield (86%) but with comparably low graphene oxide quality in terms of defect concentration, presence of oxygen functional group contamination, and crystallite properties. The aqueous NaCl, Ca(OH)2 and Mg(OH)2 electrolytes did not show any graphene oxide exfoliation effect. However, from the series of electrolytes examined, aqueous (NH4)2SO4 exhibited an excellent combination of efficient graphene oxide yield and high-quality characteristics due to its relatively high yield of 74% and superior quality of the produced graphene oxide with the comparatively lowest defect density, ?D, and highest C/O (carbon-to-oxygen) ratio. The tortuous, agglomerated, and planar layers of the distinct 2D graphene oxide sheets were also clearly revealed by the SEM images. In essence, the roles played by dissociated sulfate (SO42?), nitrate (NO32?), chlorides (Cl?), and hydroxides (OH?) ions in the series of complex electrochemical reactions toward the intercalation, exfoliation, yield, and properties of graphene oxide produced are discussed. From the series of electrolytes tested, aqueous (NH4)2SO4 emerged as the most relatively suitable electrolyte for the synthesis of graphene oxide because it combines both high yield and fine quality.

31 March 2020 in FUOYE Journal of Engineering and Technology
Verified
Journal Article
Open access
PDF file
MBMuideen Bodude
Muideen Bodude
OAOluwole Daniel Adigun
Oluwole Daniel Adigun
AIAhmed Ibrahim
Ahmed Ibrahim
AISI 1018 mild steels are widely used for engineering applications in machine components and for structural purposes. These materials suffer mechanical damages especially when used under critical conditions of extreme load. In this study, the effect of austempering heat-treatment on the hardness, tensile strength, impact energy and the microstructure of AISI 1018 steels were evaluated. The steel specimens were subjected to austempering heat-treatment by austenitizing at a temperature of 830°C, maintained at this temperature for a period of 1 hour 30 minutes, before rapidly cooled down in a NaNO3 salt bath maintained at 300°C for isothermal transformation for a further 50 minutes before finally cooled down to room temperature. Microstructural analysis using Scanning Electron Microscope (SEM) shows transformation from ferrite/pearlite to bainite microstructure. The tensile strengths of the specimen increased from 400 MPa to 500 Mpa; hardness increased from an average value of 140Rc to 162Rc; while impact energy increased from 15.6 Joule to 30.6 Joule by the austempering heat-treatment. Keywords—Austempering, hardness, tensile strength, impact energy, microstructure

3 September 2021 in Research Square
Verified
Preprint
Open access
PDF file
OAOluwole Daniel Adigun
Oluwole Daniel Adigun
MBMuyideen Adebayo Bodude
Muyideen Adebayo Bodude
AAAanuoluwapo Rebecca Adigun
Aanuoluwapo Rebecca Adigun
BOBabatunde Abiodun Obadele
Babatunde Abiodun Obadele
AAAbdullahi Olawale Adebayo
Abdullahi Olawale Adebayo
SBSunday Gbenga Borisade
Sunday Gbenga Borisade
In this study, the effects of austempering on the microstructure, mechanical properties (micro hardness, impact energy and tensile strength) and corrosion behaviours of AISI 1018 low carbon steel were evaluated. The steel specimens were subjected to heat treatment by austenitizing at 830°C, maintained in this condition for 90 min before rapid cooling in a NaNO3 salt bath sustained at 300°C for isothermal transformation for additional 50 min and finally allowed to air cool to room temperature. The as-received and the austempered samples were tested for corrosion in both 0.5M aqueous acidic (HCl) and 0. 5M alkaline (NaOH) media. Microstructural investigation using scanning electron microscope (SEM) reveals transformation from ferrite/pearlite phases to bainite over the austempering process. Interestingly, significant improvements of 15.7% to 95.7% in the various mechanical properties (micro hardness, impact energy and tensile strength) and corrosion resistance in both media were observed.

13 December 2022 in Acta Metallurgica Slovaca
Verified
Journal Article
Open access
PDF file
AAAbdullahi Adebayo
Abdullahi Adebayo
OAOlawale Olarewaju Ajibola
Olawale Olarewaju Ajibola
OFOluwasegun Falodun
Oluwasegun Falodun
SBSunday Borisade
Sunday Borisade
AOAdebayo Owa
Adebayo Owa
KAKenneth Alaneme
Kenneth Alaneme
The research investigates the effect of varying amounts of aluminium (1.05, 1.575, 2.29, 3.02 and 3.74 wt.%) addition and heat treatment (austempering at 300, 350, 400 oC) on the microstructure and mechanical properties of ductile cast iron alloys. The graphitizing effects of the Al alloy and varied austempering temperatures on hardness, tensile strength, and impact toughness of the ductile cast iron (DCI) were evaluated. The results of the influences of Al addition and heat treatment on the properties of the DCI determined were presented as graphical data while the microstructures were done by using a scanning electron microscope (SEM). The microstructures revealed that the addition of Al into the matrix brings about the precipitation of ferrite around the graphite nodules. The combined effects of the increase Al content and austempering temperatures produced greater hardness values on the Al-alloyed DCI samples than the as-cast sample. The hardness value for the entire sample ranged between 27.25 to 57.03 BHN. Tensile strength increased with an increase in Al content and lower austempering temperatures, whereas, the impact toughness increased with an increase in Al content and higher austempering temperature.