Olawale Olarewaju Ajibola

Dr. Olawale Olarewaju Ajibola

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Procedia Manufacturing
Verified
Journal Article
Open access
OAOjo Jeremiah Akinribide
Ojo Jeremiah Akinribide
SASamuel Olukayode Akinwamide
Samuel Olukayode Akinwamide
OAOlawale Olarewaju Ajibola
Olawale Olarewaju Ajibola
BOBabatunde Obadele
Babatunde Obadele
SOSamuel Oloruntoba Oluwagbenga Olusunle
Samuel Oloruntoba Oluwagbenga Olusunle
POPeter Apata Olubambi
Peter Apata Olubambi

1 January 2019 in International Journal of Refractory Metals and Hard Materials
Verified
Journal Article
Closed access
OAOjo Jeremiah Akinribide
Ojo Jeremiah Akinribide
GMGadifele Nicolene Mekgwe
Gadifele Nicolene Mekgwe
BOBabatunde Obadele
Babatunde Obadele
OAOlawale Olarewaju Ajibola
Olawale Olarewaju Ajibola
SASamuel Olukayode Akinwamide
Samuel Olukayode Akinwamide
POPeter Apata Olubambi
Peter Apata Olubambi

3 November 2015 in International Journal of Metals
Verified
Journal Article
Open access
PDF file
OAOlawale Olarewaju Ajibola
Olawale Olarewaju Ajibola
DODaniel Toyin Oloruntoba
Daniel Toyin Oloruntoba
BABenjamin O. Adewuyi
Benjamin O. Adewuyi
Effects of moulding sand permeabilities prepared from the combinations of four proportions of coarse and fine particle size mixtures and pouring temperatures varied from 700, 750, and 800 (±10°C) were studied on the hardness, porosity, strength, and microstructure of cast aluminium pistons used in hydraulic brake master cylinder. Three sand moulds were prepared from each of the 80 : 20, 60 : 40, 40 : 60, and 20 : 80 ratios. The surfaces and microstructures of cast samples were examined using high resolution microscopic camera, metallurgical microscope with digital camera, and scanning electron microscope with EDX facilities. The best of the metallurgical properties were obtained from the combination of 80 : 20 coarse-fine sand ratio and 750 ± 10°C pouring temperature using as MgFeSi inoculant. An 8 : 25 ratio of coarse to fine grained eutectic aluminium alloy was obtained with enhanced metallographic properties. The cast alloy poured at 750 ± 1°C has a large number of fine grain formations assuming broom-resembling structures as shown in the 100 µm size SEM image.

21 September 2014 in Journal of Coatings
Verified
Journal Article
Open access
PDF file
OAOlawale Olarewaju Ajibola
Olawale Olarewaju Ajibola
DODaniel T. Oloruntoba
Daniel T. Oloruntoba
BABenjamin O. Adewuyi
Benjamin O. Adewuyi
This work examined effects of hard surface polishing grits and activation on electroless-nickel (EN) plating on cast aluminium alloy substrates in sodium hypophosphite baths. As-received aluminium alloy sample sourced from automobile hydraulic brake master cylinder piston was melted in electric furnace and sand cast into rod. The cast samples were polished using different grits (60 μm–1200 μm) before plating. The effects on adhesion, appearance, and quantity of EN deposits on substrates were studied. Observation shows that the quantity of EN deposit is partly dependent on the alloy type and roughness of the surface of the substrates, whereas the adhesion and brightness are not solely controlled by the degree of surface polishing. The best yield in terms of adhesion and appearance was obtained from the activation in zincate and palladium chloride solutions. Higher plating rates (g/mm2/min) of3.01E-05,2.41E-05, and2.90E-05were obtained from chromate, zincate, and chloride than8.49E-06,8.86E-06, and1.69E-05as obtained from HCl etched, NaOH, and H2O activated surfaces, respectively.

1 October 2019 in Tribology International
Verified
Journal Article
Closed access
OIO.O. Ige
O.O. Ige
SOS.R. Oke
S.R. Oke
MMM.R. Mphahlele
M.R. Mphahlele
SAS. Aribo
S. Aribo
BOBabatunde Obadele
Babatunde Obadele
POP.A. Olubambi
P.A. Olubambi

1 January 2021 in Materials Today: Proceedings
Verified
Journal Article
Closed access
SBS.G. Borisade
S.G. Borisade
OAOlawale Olarewaju Ajibola
Olawale Olarewaju Ajibola
AAA.O. Adebayo
A.O. Adebayo
AOA. Oyetunji
A. Oyetunji