Hojjat Mousavi sogolitappeh

Mr. Hojjat Mousavi sogolitappeh

University of Tabriz, Tabrīz, Āz̄arbāyjān-e Sharqī, Iran
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2020 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
MMM.A. Mohtadi-Bonab
M.A. Mohtadi-Bonab
Hojjat Mousavi sogolitappehHojjat Mousavi sogolitappeh
Hojjat Mousavi sogolitappeh
RPReza Pourazizi
Reza Pourazizi
JSJ.A. Szpunar
J.A. Szpunar

11 October 2023 in Engineering Failure Analysis
Verified
Journal Article
Closed access
EEEhsan Entezari
Ehsan Entezari
JVJorge Luis González Velázquez
Jorge Luis González Velázquez
DLDiego Rivas López
Diego Rivas López
MZManuel Alejandro Beltrán Zúñiga
Manuel Alejandro Beltrán Zúñiga
Hojjat Mousavi sogolitappehHojjat Mousavi sogolitappeh
Hojjat Mousavi sogolitappeh
JSJerzy Szpunar
Jerzy Szpunar

11 November 2018 in Fatigue & Fracture of Engineering Materials & Structures
Verified
Journal Article
Closed access
PDF file
SHSoran Hassanifard
Soran Hassanifard
Hojjat Mousavi sogolitappehHojjat Mousavi sogolitappeh
Hojjat Mousavi sogolitappeh
AVAhmad Varvani-Farahani
Ahmad Varvani-Farahani

28 August 2022 in Metals
Verified
Journal Article
Open access
PDF file
Cyrus AminiCyrus Amini
Cyrus Amini
Ramón Jerez-MesaRamón Jerez-Mesa
Ramón Jerez-Mesa
J. Antonio Travieso-RodriguezJ. Antonio Travieso-Rodriguez
J. Antonio Travieso-Rodriguez
Hojjat Mousavi sogolitappehHojjat Mousavi sogolitappeh
Hojjat Mousavi sogolitappeh
JLJordi Llumà
Jordi Llumà
SHSoran Hassanifard
Soran Hassanifard
This paper deals with the improvement of the material surface state of friction stir welding paths modified in situ by plastic deformation through ball burnishing. The metallurgical and topological states of materials joined by this welding technique are typically detrimental to the ulterior performance of the workpiece, and it is believed that ball burnishing can improve these states to enhance functioning. This study is divided into two phases. The first one is experimental and consists of welding aluminum AA2024-T3 plates while combining different tool rotations and welding speeds. Then, the welding line is deformed locally by ball burnishing. The improvement of the topology and deep hardness distribution is measured and discussed, and the evolution of mechanical properties is assessed through tensile tests. The second phase is oriented towards estimating the residual stresses by combining two pre-existing models of friction stir welding and burnishing developed by the same authors using ANSYS®. Friction stir welding experimentation and measurements show a decrease in the values of all measured mechanical properties compared to the original material. The dominant factor affecting the properties and texture of the materials is the rotational speed of the tool, with the rupture point in the tensile test located in the distinct zone with the lowest value of microhardness on the advancing side. The higher the ratio of the rotational speed to the welding speed, the lower the roughness value. Finally, ball burnishing is proven to be an effective method to enhance the surface integrity of friction stir welded joints in light of the results, achieving a reduction of 11% to 36% in average roughness and an increase of about 22% in hardness profile, along with an integrated numerical model estimation of a remarkable effect on compressive residual stresses in-depth on the retreating side of the welded samples. However, in some tests, this treatment reduced some characteristics (yield stress and failure strain).

16 July 2025 in International Journal of Mechanical Sciences
Verified
Journal Article
Open access
AUA. Ustrzycka
A. Ustrzycka
Hojjat Mousavi sogolitappehHojjat Mousavi sogolitappeh
Hojjat Mousavi sogolitappeh
FGFrancisco Javier Dominguez Gutierrez
Francisco Javier Dominguez Gutierrez
SSS. Stupkiewicz
S. Stupkiewicz

26 March 2026 in International Journal of Plasticity
Verified
Journal Article
Closed access
Hojjat Mousavi sogolitappehHojjat Mousavi sogolitappeh
Hojjat Mousavi sogolitappeh
SSS. Stupkiewicz
S. Stupkiewicz
AUA. Ustrzycka
A. Ustrzycka