Cyrus Amini

Dr. Cyrus Amini

Arak University of Technology, Tehran, Tehrān, Iran
orcid
Assistant professor

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 May 2020 in Metals
Verified
Journal Article
Open access
PDF file
Cyrus AminiCyrus Amini
Cyrus Amini
Ramón Jerez-MesaRamón Jerez-Mesa
Ramón Jerez-Mesa
J. Antonio Travieso-RodriguezJ. Antonio Travieso-Rodriguez
J. Antonio Travieso-Rodriguez
JLJordi Llumà
Jordi Llumà
AEAida Estévez
Aida Estévez
Ball burnishing is a superfinishing operation whose objective is the enhancement of surface integrity of previously machined surfaces, hence its appropriateness to complement chip removal processes at the end of a production line. As a complex process involving plastic deformation, friction and three-dimensional interaction between solids, numerical solutions and finite element models have typically included a considerable amount of simplifications that represent the process partially. The aim of this paper is to develop a 3D numerical finite element model of the ball burnishing process including in the target workpiece real surface integrity descriptors resulting from a ball-end milled AISI 1038 surface. Specifically, its periodical topological features are used to generate the surface geometry and the residual stress tensor measured on a real workpiece is embedded in the target surface. Secondly, different models varying the effect of the coefficient of friction and the direction of application of burnishing passes with regards to the original milling direction are calculated. Results show that the resulting topology and residual stresses are independent of the burnishing direction. However, it is evident that the model outputs are highly influenced by the value of the coefficient of friction. A value of 0.15 should be implemented in order to obtain representative results through finite element models.

15 May 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
Cyrus AminiCyrus Amini
Cyrus Amini
SHSoran Hasanifard
Soran Hasanifard
MZMohammad Zehsaz
Mohammad Zehsaz
RJRamón Jerez-Mesa
Ramón Jerez-Mesa
JTJ. Antonio Travieso-Rodriguez
J. Antonio Travieso-Rodriguez

29 December 2022 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
LCLisbeth Alejandra Torres Chamorro
Lisbeth Alejandra Torres Chamorro
Cyrus AminiCyrus Amini
Cyrus Amini
NCNuria Cuadrado
Nuria Cuadrado
J. Antonio Travieso-RodriguezJ. Antonio Travieso-Rodriguez
J. Antonio Travieso-Rodriguez
JLJordi Llumà
Jordi Llumà
Montse VilasecaMontse Vilaseca
Montse Vilaseca

28 August 2022 in Metals
Verified
Journal Article
Open access
PDF file
Cyrus AminiCyrus Amini
Cyrus Amini
Ramón Jerez-MesaRamón Jerez-Mesa
Ramón Jerez-Mesa
J. Antonio Travieso-RodriguezJ. Antonio Travieso-Rodriguez
J. Antonio Travieso-Rodriguez
Hojjat Mousavi sogolitappehHojjat Mousavi sogolitappeh
Hojjat Mousavi sogolitappeh
JLJordi Llumà
Jordi Llumà
SHSoran Hassanifard
Soran Hassanifard
This paper deals with the improvement of the material surface state of friction stir welding paths modified in situ by plastic deformation through ball burnishing. The metallurgical and topological states of materials joined by this welding technique are typically detrimental to the ulterior performance of the workpiece, and it is believed that ball burnishing can improve these states to enhance functioning. This study is divided into two phases. The first one is experimental and consists of welding aluminum AA2024-T3 plates while combining different tool rotations and welding speeds. Then, the welding line is deformed locally by ball burnishing. The improvement of the topology and deep hardness distribution is measured and discussed, and the evolution of mechanical properties is assessed through tensile tests. The second phase is oriented towards estimating the residual stresses by combining two pre-existing models of friction stir welding and burnishing developed by the same authors using ANSYS®. Friction stir welding experimentation and measurements show a decrease in the values of all measured mechanical properties compared to the original material. The dominant factor affecting the properties and texture of the materials is the rotational speed of the tool, with the rupture point in the tensile test located in the distinct zone with the lowest value of microhardness on the advancing side. The higher the ratio of the rotational speed to the welding speed, the lower the roughness value. Finally, ball burnishing is proven to be an effective method to enhance the surface integrity of friction stir welded joints in light of the results, achieving a reduction of 11% to 36% in average roughness and an increase of about 22% in hardness profile, along with an integrated numerical model estimation of a remarkable effect on compressive residual stresses in-depth on the retreating side of the welded samples. However, in some tests, this treatment reduced some characteristics (yield stress and failure strain).

7 March 2024 in Journal of Composite Materials
Verified
Journal Article
Closed access
HMHojjat Mousavi
Hojjat Mousavi
Cyrus AminiCyrus Amini
Cyrus Amini
Composite materials, particularly honeycomb composites, are widely utilized in various industries, including aerospace, due to their high energy absorption against the impact and exceptional strength-to-weight ratio. This study aims to leverage the plastic and elastic properties of these materials to develop a simplified numerical model that incorporates orthotropic properties for core modeling. By doing so, the need for detailed honeycomb structure modeling is eliminated, resulting in reduced computational costs and time. A comprehensive three-dimensional finite element model, accounting for structural intricacies, is presented based on experimental data from a reputable source (isotropic model) and its equivalent finite element model (orthotropic model). The model is validated by the experimental results, demonstrating good agreement. The study also investigates parameters such as energy absorption, the internal energy of the core and faces, maximum displacement, and maximum contact force under low-velocity impact scenarios with spherical and cylindrical projectiles. These findings highlight the effectiveness of the orthotropic model, particularly in showcasing greater energy absorption in the core of the sandwich panel when subjected to a cylindrical impactor.

26 December 2022 in Scientia Iranica
Verified
Journal Article
Open access
PDF file
MBMohammad Bostan
Mohammad Bostan
Cyrus AminiCyrus Amini
Cyrus Amini
In this study, a Multi-objective Optimization Model (MOM) is developed and solved for the optimum design of surge protection devices (including air chamber and shock damper) with conflicting goals. The shock damper is a new type of surge tank invented by researchers. For the first time, the design parameters of the shock damper as decision variables are raised in a MOM problem, and results are benchmarked with solving the model for the air chamber as well. Method of characteristics (MOC) is chosen for the numerical solution of water hammer PDE’s and its system of equations for interior and boundary nodes are used as constraints of the optimization model. The conflicting criteria of the MOM are functions of safety in the system and installation cost of protection devices. In the following by using the weight coefficients and normalized objective functions obtained by dividing each of the mentioned functions by the maximum potential values of them, the resulting problem is solved by Genetic Algorithm (GA). The results, while investigated conceptually, show the significant improvement of multi-objective design in the performance and cost-saving in protection devices and the better function of shock damper regarding both criteria.