In this paper, a novel temperature compensation method for a dual-mass MEMS gyroscope is proposed based on drive mode vibration characteristic compensation using a temperature variable resistor. Firstly, the drive and sense modes of the gyroscope re analyzed and investigated, and it is found that the scale factor is proportional to the drive mode amplitude controlling reference voltage. Then, the scale factor temperature compensation method is proposed, and a temperature variable resistor is utilized to compensate the drive amplitude working point and make it change with temperature. In addition, the temperature compensation circuit is designed and simulated. After that, the temperature bias drift is compensated in a modular output. The experimental results show that scale factor and bias variation during the temperature range from −40 °C to 60 °C decrease from 3.680% to 1.577% and 3.880% to 1.913%, respectively. In addition, the bias value improves from 103.395 °/s to 22.478 °/s (optimized 78.26%). The bias stability and angular rate walking parameter are also optimized to 45.97% and 16.08%, respectively, which verify the method proposed in this paper.

The problem that the fuze overload signal sticks and is not easily identified by the counting layer during the high-speed intrusion of the projectile is an important factor affecting the explosion of the projectile in the specified layer. A three-pole plate dual-capacitance acceleration sensor based on the capacitive sensor principle is constructed in this paper. The modal simulation of the sensor structure is carried out using COMSOL 6.1 simulation software, the structural parameters of the sensor are derived from the mechanical properties of the model, and finally the physical sensor is processed and fabricated using the derived structural parameters. The mechanical impact characteristics of the model under different overloads were investigated using ANSYS/LS-DYNA, and the numerical simulation of the projectile intrusion into the three-layer concrete slab was carried out using LS-DYNA. Under different overload conditions, the sensor was tested using the Machette’s hammer test and the output signal of the sensor was obtained. The output signal was analyzed. Finally, a sensor with self-powered output, high output voltage amplitude, and low spurious interference was obtained. The results show that the ceramic capacitive sensor has a reasonable structure, can reliably receive vibration signals, and has certain engineering applications in the intrusion meter layer.

The output signal of traditional cantilever accelerometers usually overlapping and tailing during the high-velocity penetration process. And the sensitivity of traditional cantilever accelerometers cannot satisfy the application of multi-layer target penetration, that process contains large length-to-diameter ratios and high velocities. This paper proposes a novel high-impact Micro-Electro-Mechanical-System (MEMS) ceramic sandwich accelerometer (HMCSA) for the measurement of penetration-overload signals. Firstly, the HMCSA structure was designed and its structure-sensitive model was established. Then, the filling material in HMCSA was selected and the structure was simulated in ANSYS/LS-DYNA software. After that, the structure MEMS processing was introduced and the monitoring system was designed. Finally, the multi-layer target penetration process was simulated and HMCSA was tested in lab environment. The experiment verified that the design and manufacture of HMCSA was correct, and HMCSA can detect 30 000g acceleration.

Aimed at the problem of poor noise reduction effect and parameter uncertainty of pulse-coupled neural network (PCNN), a hybrid image denoising method, using an adaptive PCNN that has been optimized by grey wolf optimization (GWO) and bidimensional empirical mode decomposition (BEMD), is presented. The BEMD is used to decompose the original image into multilayer image components. After a GWO is run to complete PCNN parameter optimization, an adaptive PCNN filter method is used to remediate the polluted noise points that correspond to the different image components, from which a reconstruction of the denoised image components can then be obtained. From an analysis of the image denoising results, the main advantages of the proposed method are as follows: (i) the method effectively solves the deficiencies that arise from the critical PCNN parameter determination issue; (ii) the method effectively overcomes the problem of high-intensity noise effects by providing a more targeted and efficient noise reduction process; (iii) when using this method, the noise points are isolated, and the original pixel points are restored well, which can lead to preservation of image detail information. When compared with traditional image denoising process algorithms, the proposed method can yield a better noise suppression effect, based on indicators including analysis of mutual information (MI), structural similarity (SSIM), the peak signal-to-noise ratio (PSNR) and the standard deviation (STD). The feasibility and applicability of the proposed denoising algorithm are also demonstrated experimentally.

Snapshot-type polarization spectral imaging is a crucial dynamic high-speed target detection method in remote sensing in space because it has a high temporal resolution. However, the sparse representation of snapshot-type imaging in spectral or spatial dimension leads to low spectral or spatial resolution. To resolve the problem we propose double-channel complementary microarray coding snapshot-type polarization spectral imaging by utilizing the transmission and reflection complementary principle of a single microarray coding plate, the dual-channel multispectral and hyper-spectral image fused to enhancing the resolution of polarization spectral imaging. This study combined with the principle of intensity modulation used in full polarization measurements, and established the spectral modulation and reconstruction model of dual-channel complementary microarray coding. According to the principle of dual-channel complementary snapshot polarization spectral imaging proposed in this paper, the dual-channel multispectral and hyper-spectral image fusion model was setted up. This study improved the snapshot polarization spectral imaging spectral and spatial resolutions, increased the spatial resolution PSNR by 3 dB, and made the spectral resolution significantly higher. The findings of this study can assist in achieving high temporal resolution, high spectral resolution, high spatial resolution, and fully polarized snapshot-type polarization spectral imaging.