In this paper, an integrated double buck-boost (IDBB) converter is proposed as a high-power-factor offline power supply for power-LED lamps. The IDBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains, providing high power factor and good efficiency. In this paper, the IDBB converter is analyzed, and a design methodology is proposed. It is demonstrated that, with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures can be made as high as that of the solid-state lamp. A design example for a 70-W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.

A single-phase common-mode transformerless grid-connected photovoltaic (PV) converter, which is based on the integration of two stages, is proposed in this paper. Transformer elimination in grid-connected PV systems has many advantages. It not only reduces cost, size, and weight but also increases the complete system efficiency. Since there is no galvanic isolation between grid and PV array, a leakage current may appear due to the PV parasitic capacitance to the ground, if this is not taken into account in the converter design. This paper presents a dc/dc boost converter integrated with a full-bridge inverter. The integration of these two stages reduces the ground leakage current. The neutral line of the grid is directly connected to the negative terminal of the PV array, eliminating any possibility of leakage current in this terminal. The principle of operation of the transformerless converter is analyzed, and a 200-W topology is experimentally tested.

This paper presents the analysis and experiments of a variable inductor (VI) based LED driver for dc grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open-circuit and short-circuit protections, zero-voltage switching for the bridge transistor and zero-current switching for the output rectifier diodes, simple dynamics, possibility of analog and pulse width modulation dimming, constant switching frequency operation, and high efficiency. The converter is thoroughly analyzed and modeled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g., how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter.

DC/AC converters are widely used in several applications; traditionally, they can be classified in two types: the voltage-source inverters (VSIs) and the current-source inverters (CSIs). Their use depends on their application; however, some of them are common for both types of converters. Another possibility for the dc/ac conversion is the multilevel configuration, and the most analyzed is the VSI. In this paper, a different multilevel CSI is proposed: the paralleled configuration. To control the converter, a different sinusoidal pulse with modulation is employed; it consists of modifying the reference signal instead of using multiple carriers. Additionally, a balancing method for the inductor currents is given. The operation, analysis, and implementation are presented; moreover, simulation and experimental results are shown.

The increasing use of photovoltaic systems entails the use of new technologies to improve the efficiency and power quality of the grid. System performance is constantly increasing, but its reliability decreases due to factors such as the uncontrolled operation, the quality of the design and quantity of components, and the use of nonlinear loads that may lead to distortion in the signal, which directly affects the life of the system globally. This article presents an analysis of the reliability of a single-phase full-bridge inverter for active power injection into the grid, which considers the inverter stage with its coupling stage. A comparison between an L filter and an LCL filter, which comprise the coupling stage, is made. Reliability prediction is based on metrics, failure rate, mean time between failures, and total harmonic distortion. The analysis and numerical simulation are performed. Finally, filter considerations are suggested to extend the reliability of the inverter in a photovoltaic system.

In this paper the quadratic buck-boost (QBB) converter is proposed as a high-power-factor off-line power supply for power-LED lamps. The QBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains providing high power factor and good efficiency. In the paper, the QBB converter is analyzed and a design methodology is proposed. It is demonstrated that with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures (MTBF) can be made as high as that of the solid-state lamp. A design example for a 70 W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.