Wei Xiong

Dr. Wei Xiong

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
HHHao Huang
Hao Huang
WXWei Xiong
Wei Xiong
ZJZhen Jiang
Zhen Jiang
JZJin Zhang
Jin Zhang
An optimized homogenization process for Al alloy ingots is key to subsequent material manufacturing, as it largely reduces metallurgical defects, such as segregation and secondary phases. However, studies on their exact microstructural evolution at different homogenization temperatures are scarce, especially for complex systems, such as the 2195 Al-Cu-Li alloy. The present work aims to elucidate the microstructural evolution of the 2195 Al-Cu-Li alloy during homogenization, including the dissolution and precipitation behavior of the TB (Al7Cu4Li) phase and S (Al2CuMg) phase at different homogenization temperatures. The results show that there are Cu segregation zones (Cu-SZ) at the dendrite boundaries with θ (Al2Cu) and S eutectic phases. When the temperature rises from 300 °C to 400 °C, fine TB phases precipitate at the Cu-SZ, and the Mg and Ag in the S phases gradually diffuse into the matrix. Upon further increasing the temperature to 450 °C, TB and θ phases at the grain boundaries are coarsened, and an S-θ phase transition is observed. Finally, at 500 °C, all TB and S phases are dissolved, leaving only θ phases at triangular grain boundaries. This work provides guidance for optimizing the homogenization procedure in 2195 alloys.

17 May 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ZTZiBo Tang
ZiBo Tang
WXWei Xiong
Wei Xiong
YZYing Zheng
Ying Zheng
JZJin Zhang
Jin Zhang
In this study, single point incremental forming (SPIF) of Al-Li alloy sheets under different forming angles are studied via both experimental methods and numerical simulations. The effect of different forming angle on the geometric accuracy of SPIFed Al-Li component is studied. The simulation results show that the higher the forming angle, the lower the stress at the corner, leading to better geometrical accuracy, which is also experimentally validated. It is also found that high forming angle leads to better mechanical properties of the SPIFed Al-Li alloy component.

24 April 2025 in Materials
Verified
Journal Article
Open access
PDF file
YLYinghao Li
Yinghao Li
WXWei Xiong
Wei Xiong
Xuefan ZhouXuefan Zhou
Xuefan Zhou
Hang LuoHang Luo
Hang Luo
RGRu Guo
Ru Guo
DZDou Zhang
Dou Zhang
In this work, we introduce a high entropy effect in designing a relaxor ferroelectric (RFE)–antiferroelectric (AFE) crossover ceramic by incorporating a high entropy relaxor-like oxide (Pb0.25Ba0.25Sr0.25Ca0.25)TiO3 with antiferroelectric NaNbO3. The results show that the relaxor ferroelectricity of the system is enhanced with increasing NaNbO3, and when the new composition reaches the highest configurational entropy, stable energy storage properties can be achieved. This is enabled by a high breakdown strength due to the small grain size and stable slim ferroelectric hysteresis loop with high efficiency due to entropy-stabilized short-range ordered polar nanoregions (PNRs). These findings showcase the potential of this strategy for exploiting new compositions of high-performance electrostatic capacitors.

27 April 2023 in Metals
Verified
Journal Article
Open access
PDF file
XWXiaona Wang
Xiaona Wang
WXWei Xiong
Wei Xiong
YZYing Zheng
Ying Zheng
JZJin Zhang
Jin Zhang
Spinning extrusion forming (SEF) is a type of rheologic forming process for making complex structured aerospace components, such as ribbed cylindric shells. However, our understanding of the texture evolution and recrystallization behavior during the SEF process is still limited, especially in complex system like the 2195 Al–Li alloy, which is considered to be the ideal material candidate for aerospace vehicles because of its low density and high specific strength. In this study, we investigate the microstructural evolution of a 2195 Al–Li alloy-made cylindric shell component during SEF and subsequent solution treatment and discuss the recrystallization mechanism and its influence on the texture. It is found that particle-stimulated nucleation (PSN) occurs during the SEF process due to a large number of Al2Cu particles, which is responsible for the obvious reduction of texture components during SEF. Additionally, we show that the continuous dynamic recrystallization is responsible for the increased grains with {110} orientation, resulting in relatively stable brass texture components, even in the subsequent solution treatment.

26 October 2024 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
JZJin Zhang
Jin Zhang
DYDian Yang
Dian Yang
WXWei Xiong
Wei Xiong
DSDongfeng Shi
Dongfeng Shi
CLChenqi Lei
Chenqi Lei
GWGuoqing Wang
Guoqing Wang

31 December 2022 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
ZTZiBo Tang
ZiBo Tang
WXWei Xiong
Wei Xiong
JZJin Zhang
Jin Zhang
YZYing Zheng
Ying Zheng
CHCheng Huang
Cheng Huang