Anton Tuluk

Mr. Anton Tuluk

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2021 in Journal of Alloys and Compounds
Verified
Journal Article
Open access
ATAnton Tuluk
Anton Tuluk
TMTadhg Mahon
Tadhg Mahon
SZSybrand van der Zwaag
Sybrand van der Zwaag
PGPim Groen
Pim Groen

20 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
ATAnton Tuluk
Anton Tuluk
HBHans Brouwer
Hans Brouwer
Sybrand Van Der ZwaagSybrand Van Der Zwaag
Sybrand Van Der Zwaag
BiFeO3 is a multiferroic material with a perovskite structure that has a lot of potential for use in sensors and transducers. However, obtaining pure single-phase BiFeO3 ceramic with a low electrical conductivity via solid-state reactions remains a problem that limits its application. In this work, the suppression of secondary phases in BiFeO3 was studied by varying the compositional parameters and the sintering temperature. The addition of 1% Bi2O3 to the stoichiometric precursor mixture prevented the formation of secondary phases observed when sintering stoichiometric precursors. The pure phase ceramic had a p-type conductivity and a three-decade lower electrical conductivity as measured by impedance spectroscopy. Annealing of optimally synthesized material at different partial pressures of oxygen in an oxygen–nitrogen gas atmosphere showed that the reason for this type of conductivity lies in the high concentration of defects associated with oxygen. By annealing in various mixtures of nitrogen and oxygen, it is possible to control the concentration of these defects and hence the conductivity, which can go down another two decades. At a pO2 ≤10%, the conductivity is determined by intrinsic charge carriers in the material itself.

6 June 2022 in Journal of Applied Physics
Verified
Journal Article
Closed access
ATAnton Tuluk
Anton Tuluk
SJSiddharth Joshi
Siddharth Joshi
TMTadhg Mahon
Tadhg Mahon
Sybrand Van Der ZwaagSybrand Van Der Zwaag
Sybrand Van Der Zwaag
Bismuth ferrite is a potentially interesting lead-free piezoelectric material for use in high-temperature applications due to its high Curie temperature. However, the high coercive field and high leakage currents of pure BiFeO3 (BFO) prevent reaching its theoretical performance level. The classic approach to tailoring piezoceramic properties to their desired use conditions is the use of doping. In this work, we produce bulk BFO piezoceramic by the conventional sintering method with single element doping with cobalt (0.125–3 at. %) or titanium (1–5 at. %) and dual doping (Co and Ti added simultaneously). Cobalt doping reduces the required field for poling and also increases the leakage currents. Titanium doping reduces the leakage currents but destroys the piezoelectric properties as the coercive field strength cannot be reached. However, when both elements are used simultaneously at their appropriate levels (0.25 at. % each), a piezoelectric ceramic material is obtained, requiring a low field for full poling (9 kV/mm) and showing excellent room temperature performance such as a d33 = 40 pC/N, a dielectric constant in the region of 100 and dielectric losses less than 1%.

24 October 2023 in Materials
Verified
Journal Article
Open access
PDF file
ATAnton Tuluk
Anton Tuluk
SZSybrand van der Zwaag
Sybrand van der Zwaag
In this work, we investigated the piezoelectric properties of BiFeO3-rich (1 − (y + x)) BiFeO3–y PbTiO3–x SrTiO3 (0.1 ≤ x ≤ 0.35; 0.1 ≤ y ≤ 0.3) bulk piezoceramics, as this system could potentially lead to the development of bulk piezoelectric ceramics that are suitable for high-temperature applications (>200 °C). Samples with various levels of PbTiO3 and SrTiO3 were prepared via a conventional solid-state route. X-ray diffraction confirmed a pure perovskite phase for the compositions, which was explored without secondary phases. It was found that the addition of comparable levels of PbTiO3 and SrTiO3 to the BiFeO3 ceramic resulted in higher piezoelectric properties compared to those of the pure BiFeO3 and binary systems. The Curie temperature was significantly reduced by dual doping, with SrTiO3 and PbTiO3 additions resulting in comparable Curie temperature depressions. The locations of the phase boundaries between the cubic, pseudocubic, and rhombohedral crystal structures were determined. The highest piezoelectric properties, including a d33 value of 250 pC/N at room temperature, were obtained for the samples with the composition x = 0.3, y = 0.25, which was close to the cubic–pseudocubic phase boundary in the phase diagram. The temperature dependence of the piezoelectric properties varied depending on the previous thermal history, yet an appropriate heat treatment resulted in an almost temperature-stable d33 value. The ceramic with the lowest temperature sensitivity and a high Curie temperature of 350 °C was found for x = 0.1, y = 0.2 with a d33 value of 60 pC/N at RT and 71 pC/N at 300 °C (after poling at 60 kV/cm and a stabilizing heat treatment). However, the materials developed were still unsuitable for applications at high temperatures due to a rapidly increasing electrical conductivity with increasing temperature.

18 September 2023 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
ATAnton Tuluk
Anton Tuluk
Sybrand Van Der ZwaagSybrand Van Der Zwaag
Sybrand Van Der Zwaag
In the present work, we study the effect of quenching and annealing on the ferroelectric and piezoelectric properties at room temperature and elevated temperatures of a new ternary BiFeO3-PbTiO3-Li0.5Bi0.5TiO3 bulk piezo ceramic. While sacrificing part of the maximally obtainable piezoelectric constant value, using an optimal heat treatment, a quasi-stable value for the piezoelectric constant of 65 pC/N was obtained irrespective of the annealing temperature. All experimental results point to the direction of unusual defect behavior in this novel ternary system leading to a well-defined metastable state. The quenching and annealing process are completely reversible and can be used in combination with additional chemical modifications to tailor the properties of this new high-temperature piezoelectric ceramic to the intended use conditions.

12 May 2026 in Journal of Crystal Growth
Verified
Journal Article
Open access
ATAnton Tuluk
Anton Tuluk
ERErik de Ronde
Erik de Ronde
MSMichael Steiger
Michael Steiger
BLBarbara Lubelli
Barbara Lubelli
HMHugo Meekes
Hugo Meekes
EVElias Vlieg
Elias Vlieg