Fatigue is one of the most occurring distresses in asphalt pavements. Asphalt binder plays a critical role in fatigue behavior of asphalt mixes. Modelling and predicting fatigue behavior of binders will result in more fatigue resistant mixes. In this research, possibility of using Date Seed Ash alongside two commonly used additives (namely, a siliceous and a limestone) as bitumen modifier were investigated. Then, the influence of these additives on fatigue behavior of asphalt binders and mixes was investigated. Linear Amplitude Sweep (LAS) test was carried out and Viscoelastic Continuum Damage (VECD) parameter was determined. In addition, Indirect Tensile Fatigue Test (ITFT) was performed on mixes containing these additives. Correlation equations were developed to link fatigue behavior of binders to those of mixes. The results showed acceptable agreement between binders and mixes fatigue testing results. In addition, with predicted models it was able to obtain the asphalt binders contribution to mixes fatigue resistance. However, in the case of ash modified samples, no good correlation was observed between fatigue behavior of binders and that of mixes.
Road accidents are one of the ten major causes of death in the world. Lack of enough friction and skid resistance of the pavement surface are known as important factors in traffic accidents. In this study, to evaluate the relationship between skid resistance and pavement surface macrotexture, five methods of creating macrotexture on concrete pavements were used. Sand Patch test, British Pendulum and Wide Wheel Abrasion tests were employed to obtain mean texture depth, skid resistance and abrasion resistance of the surface, respectively. Results showed that brushing on fresh concrete surface (parallel or perpendicular to the traffic direction) can improve frictional properties of pavement surface, drastically. This method increased British Pendulum Number (BPN) and friction coefficient by 32% and 38% (in average), respectively. Friction coefficient of parallel brushing was quite similar to perpendicular (0.2% discrepancy), while its abrasion resistance was 4% higher. Hence, as a finding, parallel brushing is the most recommended texturing technique in respect to friction. Generally, concrete pavement texturing decreases surface abrasion resistance, but burlap dragging improved this index by 2.5%. Nevertheless, burlap dragging results could be deceptive due to the high sensitivity to initial setup conditions. In other words, measurement scale of the studied testing procedures are small in respect to the scale of protuberances caused by burlap dragging method.
Safety in highways is one of the most important subjects in Transportation Engineering. Increasing rate of vehicles and the needs to design or geometrically modifying the highways, emphasized on the safe-designing of the roadways more than before. Between the constructive components of the highway, horizontal curves due to the more occurrences of accidents are of great importance. The American ministry of highway and transportation introduced the software IHSDM, with variant capabilities, to predict accidents. In this research, five types of curves (simple circle curve and clothoid-circle-clothoid) at different intersection angles were designed, and accident rates based on the standard specifications on each curve was predicted by using the IHSDM, and the results are compared with each other. Finally, by processing the curves of accident rates versus the curves types and intersection angle, and comparing them with each other, the necessity of using spiral curves in the highway design is emphasized.
Pavement surface texture and its skid resistance are two key safety parameters of highways, which both are influenced by pavement characteristics. In the present study, a newly constructed asphalt pavement (Qom-Garmsar freeway) in Iran is examined. The goal is to inspect the relation between skid resistance and pavement texture in order to asphalt content changes in Hot Mix Asphalt. Mean Texture Depth (MTD) and British Pendulum Number (BPN) are being applied to quantify pavement texture and skid resistance, respectively. The results show that the asphalt content has a significant effect on MTD and consequently, BPN in loaded pavements, as well as non-loaded pavements. The result revealed that the lowest BPN value obtained, when the asphalt content is about the optimum value. Moreover, it is demonstrated that using asphalt contents less and more than the optimum value, results in BPN improvement. Asphalt content increasing, around optimum value, leads to MTD decrease. The results also reveal that by increasing the MTD, the BPN decreases to 75 (in MTD value of 0.62 mm) and then increases.