Advanced ceramics are recognized as key enabling materials possessing combinations of properties not achievable in other material classes. They provide very high thermal, chemical and mechanical resistance and typically exhibit lower densities than metals. These properties predestine ceramics for many different applications, especially those in space. Aerospike nozzles promise an increased performance compared to classic bell nozzles but are also inherently more complex to manufacture due to their shape. Additive manufacturing (AM) drastically simplifies or even enables the fabrication of very complex structures while minimizing the number of individual parts. The applicability of ceramic AM (“CerAMfacturing”) on rocket engines and especially nozzles is consequently investigated in the frame of the “MACARONIS” project, a cooperation of the Institute of Aerospace Engineering at Technische Universität Dresden and the Fraunhofer Institute for Ceramic Technologies and Systems (IKTS) in Dresden. The goal is to develop novel filigree aerospike nozzles with 2.5 N and 10 N thrust. For this purpose, CerAM VPP (ceramic AM via Vat Photopolymerization) using photoreactive and highly particle-filled suspensions was utilized. This contribution gives an overview of the component development starting from CAD modeling, suspension development based on alumina AES-11C, heat treatment and investigation of the microstructure of the sintered components. It could be shown that modifying the suspension composition significantly reduced the formation of cracks during processing, resulting in defect-free filigree aerospike nozzles for application in space.

High performance ceramics, particularly Ceramic Matrix Composite (CMC) materials found their way into liquid rocket engines. Yet, so far, mainly carbide or nonoxide CMCs have been of interest. This paper explores the potential and challenges of oxide–oxide ceramic matrix composites (OCMCs) for application in rocket thrust chambers. Therefore, strength, leakage and hot gas tests are conducted with material samples. A particular focus lies on the application of coatings to seal the permeability inherent to the material. Furthermore, prototypes in the form of flame tubes, ceramic chambers with nozzles and ceramic chambers with graphite inlays are developed and investigated experimentally in test firings. The results show that a recrystallised glass of a Y-Al-Si-O compound can successfully create an impermeable coating of the OCMC without affecting its damag-tolerant behaviour. However, the prototype developments show that it is still very challenging to manufacture even slightly complex structures without critical failures. Nevertheless, OCMC structures of relatively simple geometries showed promising results in hot firings and could be used as a lightweight housing, while the inner contour of the chamber and nozzle are realised, e.g., by a graphite inlay of appropriate quality.

Current political and sociological efforts to respond to the need for more environmentally friendly technologies have inspired a revival of wood and wood-based material utilization in space systems. The popularity of these materials has faded since their widespread use in the early days of aerospace engineering. This work reviews the literature to provide an overview of use cases, the motivation for using wood and wood-based materials and the challenges involved. A small number of applications were identified in which wood and wood-based materials were preferred over non-renewable raw materials. They are mainly applied for less-stressed disposable components or as a thermal protection material. It can be shown that the applied wooden materials have advantages such as low production costs, easy availability, easy and environment-friendly decomposition and low weight. However, only a limited number of applications have achieved a high level of technological readiness so far. Properties such as anisotropy and a lack of uniformity, defects in wood, the quantity available material and a lack of standards for the certification of wooden materials represent challenges. These are addressed in the current research, which additionally focuses on sustainable growth, enhanced environmental friendliness and advanced lightweight design.

A cold-gas test campaign has been conducted at the DLR’s P6.2 test bench in Lampoldshausen, with the objective of investigating the linear aerospike nozzle flow in interaction with secondary injection thrust vector control (SITVC). In this campaign, the influence of nozzle truncation, injection position and injection pressure on the nozzle surface and base pressure is analysed using pressure probes and Schlieren flow-visualisation techniques. The effects of injection position and truncation on the nozzle surface pressure development are comparable for all geometric variations, resulting in a locally increased static pressure upstream and a locally decreased static pressure downstream of the injection. The magnitude and dimension of these high- and low-pressure regions are correlated with the injection pressure. However, the influence of injection position and truncation on the base pressure is not entirely predictable by the named parameters, indicating an interdependence between both geometric parameters. Finally, the required pressure ratio of injection to the primary flow to ensure sonic injection has been analysed on TUD’s cold-gas test bench. This allows the respective injection position-dependent threshold to be identified. The analysis reveals that these experiments have been conducted under transsonic injection conditions.

Advanced ceramics are recognized as key enabling materials possessing combinations of properties not achievable in other material classes. They are characterized by very high thermal, chemical and mechanical resistance and also usually have a lower density than metals. These properties predestine ceramics for many different applications, especially space applications.In the aerospace sector aerospike nozzles promise performance and application advantages compared to classic bell nozzles but are also inherently more complex to manufacture due to their shape. AM methods drastically simplify or even enable the fabrication of those complex structures while minimising the number of individual parts. The applicability of ceramic AM (“CerAMfacturing”) on rocket engines and especially nozzles is consequently investigated in the frame of the “MACARONIS” project, a cooperation of the Institute of Aerospace Engineering at Technische Universität Dresden and the Fraunhofer Institute for Ceramic Technologies and Systems (IKTS) in Dresden. The goal is to develop novel large size aerospike thrust nozzles including areas of highest resolution and fineness. Finding a suitable AM process that enables the realisation of both aspects is extremely challenging. One possibility could be the hybridization of shaping methods, in that case CerAM VPP (ceramic additive manufacturing via vat photopolymerization) and CerAM FFF (ceramic additive manufacturing via fused filament fabrication) in combination with sinter joining. This contribution focuses on the high resolution CerAM VPP process, in particular the development, characterization and testing of a new photoreactive Al₂O₃ suspension validated by AM of novel aerospike nozzles.

With regard to the space field, the number of the sensors has grown for a middle-sized spacecraft from more than 500 at the beginning of the twenty-first century [1] to several thousands for nowadays applications. Meanwhile, Reusable Launch Vehicles (RLVs) moved their steps from demonstrators to commercial working systems. As a result, Health Monitoring (HM) is conquered its own space in the field and sensors are the primary elements required for implementing a monitoring unit. The innovative concept of reusable rockets requires, from the point of view of HM implementation, not only the evaluation of the vehicle health status but also the prediction of the reusability of the individual subsystems w.r.t. the next launch cycle. Therefore, the goal of this work is divided in two parts. The former is to identify the most critical points for the development of reusable rockets, focusing on theoretical working conditions and analysis or failures. The latter is to discuss the sensing units useful for addressing the defined points, describing the possible innovative approaches for sensing the system conditions. Among them, piezoelectric units, fiber optics, imaging units, and conductive layers can be identified for enhancing the comprehension of the system working conditions.