A novel early streamer emission (ESE) lightning air terminal system is designed and fabricated. By comparing the intercepted artificial lightning striking numbers of the new ESE lightning protection device and the conventional lightning rod (CLR) lightning protection device in laboratory, the effectiveness of intercepting the artificial lightning strokes by the new ESE lightning protection device is superior to that by the conventional lightning rod lightning protection device. A modified Tesla Coil (TC) discharging by powering AC voltage up to 650 kV with the controlled triggering function generator is used to produce simulated lightning strokes. The top tips of both devices in the same horizontal plane are placed at the same distance to the modified TC during all the test processes. Exchanging their positions makes no obvious difference between the recorded results. The test data validate the effectiveness of the new ESE lightning protection device under the laboratory environment.
In this work, NiCo2S4–graphene hybrids (NCS@G) with high electrochemical performance were prepared using a hydrothermal method. The response surface methodology (RSM), along with a central composite design (CCD), was used to investigate the effect of independent variables (G/NCS, hydrothermal time, and S/Ni) on the specific capacitances of the NCS@G/Ni composite electrodes. RSM analysis revealed that the developed quadratic model with regression coefficient values of more than 0.95 could be well adapted to represent experimental results. Optimized preparation conditions for NCS@G were G/NCS = 6.0%, hydrothermal time = 10.0, and S/Ni = 6.0 of NCS@G (111) sample. The maximum specific capacitance of NCS@G (111)/Ni fabricated at the optimal condition is about 216% higher than the best result obtained using the conventional experimental method. The enhanced capacitive performance of the NCS@G (111) sample can be attributed to the synergistic effect between NCS nanoparticles and graphene, which has the meso/macropores conductive network and low diffusion resistance. Notably, the NCS@G (111) could not only provide numerous reaction sites but also prevent the restacking of graphene layers. Furthermore, a supercapattery cell was fabricated with an (G + AC)/Ni anode, a NCS@G (111)/Ni cathode, and a carboxymethyl cellulose–potassium hydroxide (CMC-KOH) gel electrolyte. The NCS@G (111)//(G + AC) demonstrates an outstanding energy density of 80 Wh kg−1 at a power density of 4 kW kg−1, and a good cycling performance of 75% after 5000 cycles at 2 A g−1. Applying the synthesis strategy of RSM endows remarkable capacitive performance of the hybrid materials, providing an economical pathway to design promising composite electrode material and fabricate high-performance energy storage devices.
We examined the performance of a novel early streamer emission air terminal (ESEAT), which is used as a lightning protection device. ESEAT was tested under a laboratory-simulated lightning strike scenario and compared with a classical air terminal (CAT). The results demonstrate that ESEAT is more effective at capturing artificial lightning in the laboratory setting than CAT. Data on failed lightning captures indicate that the failure rate of the ESEAT is approximately one-tenth that of CAT. These findings validate the effectiveness of the new ESEAT in a controlled laboratory environment.
The methods to improve the performances of a High-Temperature Proton Exchange Membrane Fuel Cell (HT-PEMFC) have been studied. Two approaches were tested: the catalyst layer (CL) combination and external temperature control. The CL structures, properties, binder, and platinum/carbon (Pt/C) concentration were chosen as perimeters to find the best CL combination. The lowest weight percentage of Pt/C, provides the thickest CL with a smaller size and uniform distribution of Pt catalyst. Consequently, the electrochemical reaction can easily happen. The Polytetrafluoroethylene (PTFE) binder provides a higher gas permeability, resulting in more gases diffusing to the working area. The maximum current density of 0.62 A/cm2 and the highest power density of 190.15 mW/cm2 at 0.3067 V was reached, and the best combination of CL is 10 wt% Pt/C with PTFE binder. Temperature control of HT-PEMFC stack with heat pipe (HP) is also successfully proved. Both heating and cooling by HP provide a more uniform temperature distribution in the working area and a low-temperature gradient across the stack than the commonly used technique for controlling fuel cell temperature.