A highly sensitive and selective formaldehyde sensor was successfully fabricated using hybrid materials of nitrogen-doped double-walled carbon nanotubes (N-DWCNTs) and polyvinylpyrrolidone (PVP). Double-walled carbon nanotubes (DWCNTs) and N-DWCNTs were produced by high-vacuum chemical vapor deposition using ethanol and benzylamine, respectively. Purified DWCNTs and N-DWCNTs were dropped separately onto the sensing substrate. PVP was then dropped onto pre-dropped DWCNT and N-DWCNTs (hereafter referred to as PVP/DWCNTs and PVP/N-DWCNTs, respectively). As-fabricated sensors were used to find 1,2-dichloroethane, dichloromethane, formaldehyde and toluene vapors in parts per million (ppm) at room temperature for detection measurement. The sensor response of N-DWCNTs, PVP/DWCNTs and PVP/N-DWCNTs sensors show a high response to formaldehyde but a low response to 1,2-dichloroethane, dichloromethane and toluene. Remarkably, PVP/N-DWCNTs sensors respond sensitively and selectively towards formaldehyde vapor, which is 15 times higher than when using DWCNTs sensors. This improvement could be attributed to the synergistic effect of the polymer swelling and nitrogen-sites in the N-DWCNTs. The limit of detection (LOD) of PVP/N-DWCNTs was 15 ppm, which is 34-fold higher than when using DWCNTs with a LOD of 506 ppm. This study demonstrated the high sensitivity and selectivity for formaldehyde-sensing applications of high-performance PVP/N-DWCNTs hybrid materials.
26 January 2016 in Japanese Journal of Applied Physics
Poly(methyl methacrylate) (PMMA) and thiophene-coated single-walled carbon nanotubes (SWNTs) were fabricated for use in volatile organic compound (VOC) detection. Pristine SWNTs were separately coated with PMMA (PMMA/SWNTs) and thiophene (thiophene/SWNTs) by spin-coating. Pristine SWNTs showed the highest response to methanol, while PMMA/SWNTs enabled 5.4-fold improved dichloromethane detection and thiophene/SWNTs enabled 1.4-fold improved acetone detection compared with pristine SWNTs. The sensor response of PMMA/SWNTs to dichloromethane and that of thiophene/SWNTs to acetone can be attributed to the Hildebrand solubility parameter (HSP). The more similar the HSP, the higher the sensor response. The sensor response of pristine SWNTs to methanol is related to the diffusion coefficient and molecular size. The relationships between the vapor concentration and sensor response of PMMA/SWNTs to dichloromethane and thiophene/SWNTs to acetone are based on Henry’s adsorption isotherm, while that of pristine SWNTs to methanol is based on the Henry–clustering model. Principal component analysis (PCA) results show that dichloromethane, acetone, and methanol were successfully discriminated.
Nitrogen-doped activated carbon (N-AC) was successfully prepared by KOH-activation and nitrogen doping using ammonia (NH3) heat treatment. Coconut shell-derived activated carbon (AC) was heat-treated under NH3 gas in the temperature range of 700°C–900°C. Likewise, the mixture of potassium hydroxide (KOH) and AC was heated at 800°C, followed by heat treatment under NH3 gas at 800°C (hereafter referred to as KOH-N-AC800). Scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) method were utilized to analyze morphology, crystallinity, chemical bonding, chemical composition and surface area. The surface area and porosity of N-AC increased with increasing NH3 heat treatment. Similarly, the nitrogen content in the N-AC increased from 3.23% to 4.84 at% when the NH3 heat treatment was raised from 700°C to 800°C. However, the nitrogen content of N-AC decreased to 3.40 at% after using NH3 heat treatment at 900°C. The nitrogen content of KOH-N-AC800 is 5.43 at%. KOH-N-AC800 and N-AC800 exhibited improvements of 33.66% and 26.24%, respectively, in CO2 adsorption compared with AC. The enhancement of CO2 adsorption of KOH-N-AC800 is attributed to the synergic effect of the nitrogen doping, high surface area, and porosity. The results exhibited that nitrogen sites on the surface play a more significant role in CO2 adsorption than surface area and porosity. This work proposes the potential synergistic effect of KOH-activation and nitrogen doping for enhancing the CO2 adsorption capacity of activated carbon.
Herein, cure characteristics, morphology, and mechanical properties of natural rubber filled with activated carbon-based materials were investigated. Carbon-based materials were prepared from bagasse, coffee grounds and pineapple crowns by the pyrolysis method at temperatures in the range of 300°C. As-synthesized carbon materials were characterized by optical microscopy (OM), scanning electron microscopy (SEM), and Fourier-transform infrared spectroscopy (FTIR) to analyze size distribution, morphology, and functional groups, respectively. OM and SEM analysis revealed that particles, flakes, and a small quantity of fiber-like carbon were obtained using bagasse and pineapple crown as raw materials, while honeycomb-like carbon materials can be derived from coffee grounds. To investigate the mechanical properties, natural rubber was filled with carbon black and as-synthesized carbon materials by the internal mixing and compression molding process. Transmission electron microscopy (TEM) was utilized to characterize the dispersion of carbon materials in the rubber matrix. The results of tensile testing showed that the natural rubber mixed with as-synthesized carbon materials from pineapple crowns exhibited 54% and 74% improvement in the ultimate tensile strength and Young’s modulus, respectively, compared with natural rubber without filled carbon materials. The enhancement in mechanical properties by activated carbon materials derived from pineapple crowns can be attributed to the flake- and fiber-like structures and good dispersion of carbon materials in the rubber matrix. In addition, it is higher than that of rubber mixed with carbon black. The results demonstrated that as-synthesized carbon materials from pineapple crowns have the potential materials to substitute carbon black in the rubber compound industry.