Visittapong Yordsri

Mr. Visittapong Yordsri

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 February 2024 in Materials
Verified
Journal Article
Open access
PDF file
KPKattaliya Petchnui
Kattaliya Petchnui
TUTeerayut Uwanno
Teerayut Uwanno
MRMayuree P. Reilly
Mayuree P. Reilly
CPChinathun Pinming
Chinathun Pinming
ATAlongkot Treetong
Alongkot Treetong
Winadda WongwiriyapanWinadda Wongwiriyapan
Winadda Wongwiriyapan
Triboelectric nanogenerators (TENGs) have gained significant attention as promising energy-harvesting devices that convert mechanical energy into electrical energy through charge separation induced by friction and electrostatic induction. In this study, we explore the utilization of biowaste shrimp shell-extracted chitin nanofiber (ChNF) as a viable eco-friendly material for TENG applications. Composite materials were prepared by incorporating ChNF into natural rubber (NRL) at loading levels of 0.1 and 0.2 wt% (NRL/ChNF) to form the TENG triboelectric layer. ChNFs with a uniform width of approximately 10–20 nm were successfully extracted from the shrimp shells through a simple mechanical procedure. The NRL/ChNF composites exhibited enhanced mechanical properties, as evidenced by a higher Young’s modulus (3.4 GPa) compared to pure NRL. Additionally, the NRL/ChNF composites demonstrated an increased dielectric constant of 3.3 at 0.1 MHz. Moreover, the surface potential difference of NRL increased from 0.182 V to 1.987 V in the NRL/ChNF composite. When employed as the triboelectric layer in TENG, the NRL/ChNF composites exhibited significant improvement in their output voltage, with it reaching 106.04 ± 2.3 V. This enhancement can be attributed to the increased dielectric constant of NRL/ChNF, leading to enhanced charge exchange and charge density. This study presents a straightforward and environmentally friendly technique for preparing sustainable natural materials suitable for energy-harvesting devices.

30 November 2022 in Sensors
Verified
Journal Article
Open access
PDF file
TCThanattha Chobsilp
Thanattha Chobsilp
TTThotsaphon Threrujirapapong
Thotsaphon Threrujirapapong
VYVisittapong Yordsri
Visittapong Yordsri
ATAlongkot Treetong
Alongkot Treetong
SISaowaluk Inpaeng
Saowaluk Inpaeng
WMWorawut Muangrat
Worawut Muangrat
A highly sensitive and selective formaldehyde sensor was successfully fabricated using hybrid materials of nitrogen-doped double-walled carbon nanotubes (N-DWCNTs) and polyvinylpyrrolidone (PVP). Double-walled carbon nanotubes (DWCNTs) and N-DWCNTs were produced by high-vacuum chemical vapor deposition using ethanol and benzylamine, respectively. Purified DWCNTs and N-DWCNTs were dropped separately onto the sensing substrate. PVP was then dropped onto pre-dropped DWCNT and N-DWCNTs (hereafter referred to as PVP/DWCNTs and PVP/N-DWCNTs, respectively). As-fabricated sensors were used to find 1,2-dichloroethane, dichloromethane, formaldehyde and toluene vapors in parts per million (ppm) at room temperature for detection measurement. The sensor response of N-DWCNTs, PVP/DWCNTs and PVP/N-DWCNTs sensors show a high response to formaldehyde but a low response to 1,2-dichloroethane, dichloromethane and toluene. Remarkably, PVP/N-DWCNTs sensors respond sensitively and selectively towards formaldehyde vapor, which is 15 times higher than when using DWCNTs sensors. This improvement could be attributed to the synergistic effect of the polymer swelling and nitrogen-sites in the N-DWCNTs. The limit of detection (LOD) of PVP/N-DWCNTs was 15 ppm, which is 34-fold higher than when using DWCNTs with a LOD of 506 ppm. This study demonstrated the high sensitivity and selectivity for formaldehyde-sensing applications of high-performance PVP/N-DWCNTs hybrid materials.