Yupeng Shen

Dr. Yupeng Shen


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 June 2019 in Materials
Verified
Journal Article
Open access
PDF file
LZLei Zhang
Lei Zhang
ZHZhifu Huang
Zhifu Huang
YLYangzhen Liu
Yangzhen Liu
YSYupeng Shen
Yupeng Shen
KLKemin Li
Kemin Li
Yongxin JianYongxin Jian
Yongxin Jian
Mo2NiB2-Ni cermets have been extensively investigated due to their outstanding properties. However, studies have not systematically examined the effect of the powder milling process on the cermets. In this study, Mo, Ni, and B raw powders were subjected to mechanical ball milling from 1 h to 15 h. XRD patterns of the milled powders confirmed that a new phase was not observed at milling times of 1 h to 15 h. With the increase in the mechanical ball milling time from 1 h to 11 h, raw powders were crushed to small fragments, in addition to a more uniform distribution, and with the increase in the mechanical ball milling time to greater than 11 h, milled powders changed slightly. Mo2NiB2-Ni cermets were fabricated by reaction boronizing sintering using the milled powders at different ball milling times. The milling time significantly affected the microstructure and mechanical properties of Mo2NiB2-Ni cermets. Moreover, the Mo2NiB2 cermet powder subjected to a milling time of 11 h exhibited the finest crystal size and the maximum volume fraction of the Mo2NiB2 hard phase. Furthermore, the cermets with a milling time of 11 h exhibited a maximum hardness and bending strength of 87.6 HRA and 1367.3 MPa, respectively.

17 April 2020 in Materials
Verified
Journal Article
Open access
PDF file
YSYupeng Shen
Yupeng Shen
ZHZhifu Huang
Zhifu Huang
LZLei Zhang
Lei Zhang
KLKemin Li
Kemin Li
ZCZhen Cao
Zhen Cao
Yongxin JianYongxin Jian
Yongxin Jian
Four series of Mo2FeB2-based cermets with Ti contents between 0 wt.% and 1.5 wt.% in 0.5 wt.% increments were prepared by in situ reaction and liquid phase sintering technology. Influences of Ti on microstructure and mechanical properties of cermets were studied. It was found that Ti addition increases formation temperatures of liquid phases in liquid-phase stage. Ti atoms replace a fraction of Mo atoms in Mo2FeB2 and the solution of Ti atoms causes the Mo2FeB2 crystal to be equiaxed. In addition, the cermets with 1.0 wt.% Ti content exhibit the smallest particle size. The solution of Ti atoms in Mo2FeB2 promotes the transformation of Mo2FeB2 particles from elongated shape to equiaxed shape. With Ti content increasing from 0 wt.% to 1.5 wt.%, the hardness and transverse rupture strength (TRS) first increase and then decrease. The maximum hardness and TRS occur with 1.0 wt.% Ti content. However, the fracture toughness decreases as Ti content increases. The cermets with 1.0 wt.% Ti content show excellent comprehensive mechanical properties, and the hardness, fracture toughness, and TRS are HRA 89.5, 12.9 MPa∙m1/2, and 1612.6 MPa, respectively.

1 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
YLYajin Li
Yajin Li
BSBingbing Sun
Bingbing Sun
YLYunfei Liu
Yunfei Liu
ZZZhengzhong Zhang
Zhengzhong Zhang
YSYupeng Shen
Yupeng Shen
WXWuxi Xie
Wuxi Xie
Pseudo-semi interpenetrating polymer networks (pseudo-semi IPNs) are a special example of topological isomerism in macromolecules, which have attracted significant attention in recent years with a high potential in a variety of engineering applications of polymeric materials. In this article, pseudo-semi IPNs were synthetized by sequential polymerization of thermoplastic polymers (TPEs) in the presence of thermosetting elastomer (TSEs) with contents of 10, 20, 30, 40 and 50 wt.% in a vacuum oven at 60 °C for about 72 h. In addition, this article describes a method for researching the elastic modulus, effective crosslinking density and physical crosslinking density of TSEs and pseudo-semi IPNs. The inherent interactions and entanglements of pseudo-semi IPNs were discussed by analyzing the changes in elastic modulus and effective crosslinking density at different temperatures. The results show that after the TPE was added to the TSE matrix as a plastic-reinforced material, the ductility increased from 89.6% to 491%, the effective crosslinking density was increased by 100% at high temperatures and the strength of the material matrix was significantly improved. Two physical events take place in our pseudo-semi IPNs as result of energy dissipation and polymeric chains mobility.

28 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
YSYupeng Shen
Yupeng Shen
WXWuxi Xie
Wuxi Xie
BSBingbing Sun
Bingbing Sun
YLYunfei Liu
Yunfei Liu
YLYajin Li
Yajin Li
ZHZhifu Huang
Zhifu Huang
Mo2FeB2-based cermets have wide applications in fields of wear resistance, corrosion resistance and heat resistance due to their simple preparation process, low-cost raw materials, and prominent mechanical properties. Herein, Mo2FeB2-based cermets with xMo (x = 43.5, 45.5, 47.5, 49.5, wt.%) were prepared by means of the vacuum liquid phase sintering technique. Investigations on the microstructure and mechanical properties of Mo2FeB2-based cermets with Mo addition were performed. Experimental results show that, with Mo content increasing, the average particle size decreases gradually, revealing that the grain coarsening of Mo2FeB2-based cermets is controlled by interface reaction. In addition, Mo2FeB2 grains gradually transform from an elongated shape to a nearly equiaxed shape. The improvement of Mo2FeB2 hard phase on the morphology is mainly due to the inhibition of solution–precipitation reaction by increasing Mo. Furthermore, the relative density of cermets decreases due to the reduced Fe content. When Mo content is 47.5 wt.%, a relatively small grain size of Mo2FeB2 is obtained (about 2.03 μm). Moreover, with the increase in Mo content, hardness and transverse rupture strength (TRS) of Mo2FeB2-based cermets increase firstly and then decrease. Whereas, with increasing Mo content, the fracture toughness deteriorates gradually. When Mo content is 47.5 wt.%, the comprehensive mechanical properties of cermets are the best. The optimal raw material ratio for the preparation of Mo2FeB2-based cermets in this study is determined to be 47.5 wt.% Mo–6.0 wt.% B-Fe.