Yajin Li

Dr. Yajin Li

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

4 August 2020 in Propellants, Explosives, Pyrotechnics
Verified
Journal Article
Closed access
PDF file
YLYajin Li
Yajin Li
WXWuxi Xie
Wuxi Xie
HWHaiyang Wang
Haiyang Wang
HYHongtao Yang
Hongtao Yang
HHHaitao Huang
Haitao Huang
XFXuezhong Fan
Xuezhong Fan

1 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
YLYajin Li
Yajin Li
BSBingbing Sun
Bingbing Sun
YLYunfei Liu
Yunfei Liu
ZZZhengzhong Zhang
Zhengzhong Zhang
YSYupeng Shen
Yupeng Shen
WXWuxi Xie
Wuxi Xie
Pseudo-semi interpenetrating polymer networks (pseudo-semi IPNs) are a special example of topological isomerism in macromolecules, which have attracted significant attention in recent years with a high potential in a variety of engineering applications of polymeric materials. In this article, pseudo-semi IPNs were synthetized by sequential polymerization of thermoplastic polymers (TPEs) in the presence of thermosetting elastomer (TSEs) with contents of 10, 20, 30, 40 and 50 wt.% in a vacuum oven at 60 °C for about 72 h. In addition, this article describes a method for researching the elastic modulus, effective crosslinking density and physical crosslinking density of TSEs and pseudo-semi IPNs. The inherent interactions and entanglements of pseudo-semi IPNs were discussed by analyzing the changes in elastic modulus and effective crosslinking density at different temperatures. The results show that after the TPE was added to the TSE matrix as a plastic-reinforced material, the ductility increased from 89.6% to 491%, the effective crosslinking density was increased by 100% at high temperatures and the strength of the material matrix was significantly improved. Two physical events take place in our pseudo-semi IPNs as result of energy dissipation and polymeric chains mobility.

28 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
YSYupeng Shen
Yupeng Shen
WXWuxi Xie
Wuxi Xie
BSBingbing Sun
Bingbing Sun
YLYunfei Liu
Yunfei Liu
YLYajin Li
Yajin Li
ZHZhifu Huang
Zhifu Huang
Mo2FeB2-based cermets have wide applications in fields of wear resistance, corrosion resistance and heat resistance due to their simple preparation process, low-cost raw materials, and prominent mechanical properties. Herein, Mo2FeB2-based cermets with xMo (x = 43.5, 45.5, 47.5, 49.5, wt.%) were prepared by means of the vacuum liquid phase sintering technique. Investigations on the microstructure and mechanical properties of Mo2FeB2-based cermets with Mo addition were performed. Experimental results show that, with Mo content increasing, the average particle size decreases gradually, revealing that the grain coarsening of Mo2FeB2-based cermets is controlled by interface reaction. In addition, Mo2FeB2 grains gradually transform from an elongated shape to a nearly equiaxed shape. The improvement of Mo2FeB2 hard phase on the morphology is mainly due to the inhibition of solution–precipitation reaction by increasing Mo. Furthermore, the relative density of cermets decreases due to the reduced Fe content. When Mo content is 47.5 wt.%, a relatively small grain size of Mo2FeB2 is obtained (about 2.03 μm). Moreover, with the increase in Mo content, hardness and transverse rupture strength (TRS) of Mo2FeB2-based cermets increase firstly and then decrease. Whereas, with increasing Mo content, the fracture toughness deteriorates gradually. When Mo content is 47.5 wt.%, the comprehensive mechanical properties of cermets are the best. The optimal raw material ratio for the preparation of Mo2FeB2-based cermets in this study is determined to be 47.5 wt.% Mo–6.0 wt.% B-Fe.

4 September 2020 in Zeitschrift für Kristallographie - New Crystal Structures
Verified
Journal Article
Open access
PDF file
YLYajin Li
Yajin Li
XWXie Wuxi
Xie Wuxi
SKSong Kuanguang
Song Kuanguang
ZYZhao Yu
Zhao Yu
C16H10CuN14O8, monoclinic, C2/c (no. 15), a = 13.4851(13) Å, b = 12.3808(12) Å, c = 13.2151(13) Å, β = 97.3040(10)°, V = 2188.4(4) Å3, Z = 4, Rgt(F) = 0.0310, wRref(F2) = 0.1127, T = 296(2) K.