Coconut shell concrete is one of the recently established lightweight concretes. This paper discusses the optimization of adding coconut fibers in both coconut shell concrete and conventional concrete. Coconut fibers at different aspect ratios of 16.67, 33.33, 50, 66.67, 83.33, and 100 and volume fractions of 1, 2, 3, 4, and 5% were tried. The maximum compressive strength was attained at an aspect ratio of 83.33 and volume fraction of 3% for conventional concrete, and aspect ratio 66.67 and volume fraction 3% for coconut shell concrete. Flexural strength increased by 30.63% (conventional concrete) and 53.66% (coconut shell concrete) on the addition of coconut fibers. Similarly, the split tensile strength increased by 19.44% and 30%, respectively. The number of blows needed for failure of specimen in impact resistance test was more for concrete mixed with fibers. The experimental bond stresses were higher than the theoretical values recommended by IS 456: 2000 (Indian Standard) and BS 8110 (British Standard). This study shows that the addition of coconut fiber enhances the properties of both conventional and coconut shell concrete.
Coconut fiber was used in coconut shell concrete (CSC) and its durability properties were studied. The properties include: water absorption, volume of permeable pore voids, rapid chloride penetration test, sorptivity and resistance at elevated temperature. For comparison purpose, these properties were also studied on conventional concrete (CC) with coconut fibers. Three different curing conditions viz. full water immersion, site curing and air-dry conditions were employed except for temperature resistance study in which only full water immersion was used. Test results show that the durability properties were better in full water immersion condition in case of CC mixes and in site curing condition in case of CSC mixes. Temperature resistance tests gave a minimum guarantee of both CC and CSC mixes without and with coconut fibers for 2 h resistance and hence they were deemed safe for construction.
Construction disputes have become a recurrent phenomenon in the industry, due to which progress is halted. From a bird’s eye perspective, the most frequent cause of a dispute might be payment issues. However, when observed keenly, it has an inter-relationship with almost every other cause, such as contractual changes, delays in project completion, compromising on the quality of construction, etc. Therefore, analyzing the factors which cause a dispute is important. It is also essential to understand the interrelationship of the factors. In this study, judicial construction disputes, along with judgements in different domains, were collected. The most frequent causes of disputes are identified among these cases. Sixty-five cases were considered for the analysis, which constitutes the writ petition, response and final judgment. These items were collected to gain the perspective of the petitioners and respondents over the cause of the dispute and the final judgment to analyze the factors responsible for decision-making. Factor analysis is done to find out the influencing factors, interrelationships and similarities of the disputes respectively. Among the 8 major factors identified, a strong, positive correlation was found between Poor Performance related issues and Payment related issues. By performing Principal Component Analysis (PCA), causes were classified into 3 domains based on their variables.
The utilization of waste materials in concrete lowers its cost, and this method of dealing with the problem of trash disposal is viewed as the most environmentally friendly. Fly Ash Cenospheres (FAC) are one of the principal wastes produced by coal power stations. The huge volume of FAC produced worldwide has created a sustainability challenge, owing to the potential implications of inappropriate disposal. Using cenospheres in concrete materials would make effective and efficient use of these waste products while also supplementing what the present raw material, such as river sand, can supply for concrete material production. Though the application of FAC in concrete is currently carried out by the construction industry, there is still a lack of understanding about its performance in concrete with Manufactured Sand (M Sand) as fine aggregate. Therefore, in this paper, a comprehensive study explores the concept of adding FAC to M Sand concrete. The properties of fresh and hardened concrete, such as density, workability, compression, split tensile, flexure, and impact resistance after the addition of FAC in volume replacement (0–100% with a difference of 5% at thirteen different ratios) is represented, followed by microstructural analysis. From the results, it can be concluded that strength reduction takes place as FAC content increases from 0–100%, however, the strength is within the target limit of 31.2 N/mm2 of conventional concrete (CC) of grade M25 when the percentage replacement is below 35% of volume. Therefore, reducing the volume of fine aggregate does not negatively affect the strength properties, but also impacts the environmental concern positively with optimum recommendation of 35% of fine aggregate as FAC.
15 August 2023 in Asian Journal of Civil Engineering
The usage of foam concrete (FC) was extended from being used as a filler material to an alternative concrete due to the effect of conventional concrete on global warming. The diversified perspective on FC as an alternative to conventional concrete is due to its low density (400–1800 kg/m3) and good thermal conductivity, which also results in the reduction of costs in production, labor, and transportation. Generally, FC is produced by adding a pre-made foam to the cement slurry consisting of cement and aggregates. Here, the study was carried out by the addition of a coarse aggregate and foaming agent (i.e., 12%, 6%, 3%, 2%, 1%) at varying percentages in FC to improve the strength characteristics. FC was tested for its physical and mechanical properties. From the experimental results, an Artificial Neural Network (ANN) was developed to predict the strength of FC. The results from training and testing of the Polynomial Regression Analysis model (PRA) through ANN have shown great potential in predicting compression, split tensile, and flexural strength of FC. It was found that the strength of FC is increased with the reduction of foam volume and increase in coarse aggregate volume. However, a strength of 25.6 N/mm2 is achieved when 1% foam and 50% coarse aggregate is used.