In this research, a directional reduction charging structure was proposed to solve the problems caused by drilling and blasting method such as serious damage to surrounding rocks, working face low contour flatness and serious over-under break of root base c. Drilling and blasting tests, numerical calculations and field applications were designed and performed for the verification of the blasting advantages of charge structure. Test results showed that the peak positive strain along the protection direction of directional protection shaped charge was significantly smaller than that of ordinary charge, where PVC material presented the strongest effect such that the peak positive strain of specimen 1 at measuring point 4 (protection direction) was only 0.27 times that at measuring point 9 (non-protected direction). Numerical simulations indicated shaped jet formation, damage-reduction and charge penetration process and obtained the force law of cement target plate. Experimental results revealed that application of charge in tunnel controlled blasting achieved a clear controlling effect on contour line excavation. Compared with ordinary smooth blasting method, all technical indicators of the developed method were improved such that half hole mark rate was increased by about 33% and the amount of over-under break was decreased by about two times. Research results are of certain significance for the stability of surrounding reserved rocks and formation of roadway in blasting engineering and the developed method was found to be applicable to mining, shaft excavation and other projects.
For shaped charge blasting projects in mining, civil engineering, and similar fields, it is proposed to modify the charge structure by combining slotted tubes and shaped charge liners to obtain a new type of charge structure. This aims to achieve directional rock breaking through the focused action of the shaped charge. The influence of different slotted pipe materials on the directional rock-breaking effect of concentrated energy using a new charge structure is explored through theoretical analysis combined with model test study, high-speed camera, stress–strain gauge, and other equipment. A comparison is made between slotted pipes made of aluminum, kraft paper, and PVC, with the cutting width of 2 mm. Based on the characteristics of the cracks formed after blasting, the new charge structure made of aluminum slotted pipe produces a penetrating crack that is almost consistent with the pre-cracking direction. Based on the corresponding characteristics of successively released blasting energy, the guiding and convergence effect of the new charge structure made of aluminum slotted pipe on the explosion energy is greater than that of the new charge structure made of the other two types of slotted pipe material. According to the strain data measured after blasting, the peak arrival time of the strain peak in the direction of the slotted pipe on one side of the shaped hood is shorter than that in the other two directions, and the peak strain is greater than that in the other two directions while having a better energy gathering effect. Based on the findings, the new charge structure with directional energy concentration has a damage reduction effect. Furthermore, the material of aluminum slotted pipe is found to be better than PVC slotted pipe, whereas the material of PVC slotted pipe is better than kraft paper slotted pipe in achieving directional rock breaking.
31 December 2015 in Journal of Vacuum Science & Technology B
In this work, the authors report the incorporation of TiW alloy in InGaN/GaN-based flip-chip light-emitting diodes (LEDs). The advantages provided by the use of TiW are analyzed in detail. InGaN/GaN multiple quantum well LEDs with a Ni/Ag/TiW metal stack are found to tolerate high-temperature annealing better than those with a Ni/Ag metal stack. Highly improved current–voltage characteristics and enhanced optical output power are achieved for the devices with a TiW thin layer. These changes are ascribed to the higher reflectivity, smoother surface, and better ohmic properties of the device containing TiW after annealing. Better heat management of the device with TiW is demonstrated by comparing electroluminescence spectra of the two device structures. Overall, these factors resulted in devices with TiW exhibiting a higher external quantum efficiency than devices without TiW. Detailed x-ray photoelectron spectroscopy analyses of the reflector metal stacks reveal little intermixing of the layers after annealing in the devices with TiW. The results show that incorporation of TiW is a promising approach for the fabrication of high-performance InGaN/GaN flip-chip LEDs.
Solving the problem of gas extraction from low-permeability coal seams is an urgent issue in the global coal industry, and exploring green and efficient mining methods has potential applications in this field. In this study, the No. 9 coal seam of the Guizhou Longfeng Coal Mine was selected as the research object. The method of using a hydraulic horizontal slit to create a compensation space and then synergizing it with the coal body’s own stress to decompress and increase the permeability of the coal body was studied through similarity simulation and numerical simulation experiments. This study showed that the slit can cause the overall development, expansion, and penetration of coal seam fissures. Thereby, a large number of fissures are produced in the coal seam and its upper rock layer, which form, as a whole, a “positive trapezoid” shape. The three stages of the slit produced 165, 487, and 1572 fissures, which unpressurized and increased the penetration of the coal and rock body. The slit causes the upper coal body to lose its support, and the original stress balance of the coal and rock is broken, forming a decompression zone. At the same time, the coal body below starts to expand and deform after losing the vertical stress. The decompression zone gradually expands up and down, and the stress on both ends of the compensation space becomes larger, forming a stress concentration area. After the overall displacement of the coal seam caused by the slit, a “positive triangle” area is formed. In the upper part of the area, six displacement dividing lines are created, which form five areas. The displacement shows the distribution characteristics of a large displacement in the middle and a small displacement at both ends. The results of the similarity simulation and numerical simulation experiments were verified. The study provides a new way of thinking for effectively preventing coal and gas protrusion and improving mining efficiency.
This study compared models of specimens with different filler media and decoupled charge structures in terms of the blasting effect. The test system combined a high-speed camera and high-speed static strain test analyzer. A physical model of a concrete single-borehole decoupled charge structure was designed to study the geometric elements of the blasting funnel, flyrock launch velocity, peak strain values, and distribution of the gravel lumpiness. The experimental results showed that for the same decoupling coefficient, when expandable polystyrene foam (EPS) was used as the filling medium, the radius, depth, and volume of the blasting funnel of the model specimen were larger, the flyrock launch velocity was slower, the peak stress of the specimen was higher, and the distribution of gravel lumpiness was more even. The relationship between the experimental index and the decoupling coefficient follows the changing trend of first increasing and then decreasing or first decreasing and then increasing. With air and EPS as the filling media, the concrete model specimens could achieve optimal blasting effects at decoupling coefficients of 1.83 and 1.69, respectively. The results confirm the feasibility and practicability of using EPS as a filler and can provide guidance and an experimental basis for the selection of the decoupling coefficient and filling medium in blasting engineering.