3 January 2024 in Materials Today Physics
21 July 2021 in ACS Photonics
15 April 2024 in Applied Physics Letters
AlGaN multiple-quantum-well diode-based solar-blind ultraviolet emission-detection monolithic integration system shows great application value due to its advantages of multifunctionality, secure communication, and anti-interference ability. To reduce the lateral optical propagation loss and improve the emitting light detection efficiency, we have proposed a concentric ring-circle configuration for the system, where the out-ring light-emitting diode is the emitter at 253 and 267 nm, and the inner-circle detector is the receiver. The out-ring light-emitting diode exhibits about twice the injection current at the same bias and slightly higher light output power at the same current due to better current spreading and sidewall light extraction compared to the conventional square–square configuration. Simultaneously, the concentric inner-circle detector maximizes the collection of the emitted light flux. Under the emission-detection mode for the monolithic integration system, compared to the conventional square–square configuration, the concentric ring-circle design presents an improvement in the ratio of emitter injection current to detector output photocurrent and higher output signal amplitude under the same transmission work mode, demonstrating the improved system energy and coupling efficiency. This design provides a potential approach to achieve low power consumption and high bandwidth in the monolithic integrated optoelectronic chips.
18 April 2025 in Optics Letters
Deep-ultraviolet (DUV) micro-LEDs are pivotal for applications such as maskless lithography and germicidal disinfection. However, improving light extraction efficiency (LEE) remains a significant challenge. This study presents a novel, to the best of our knowledge, strategy to enhance LEE by employing gold thin-film annealing and dry-etching techniques to fabricate disordered p-GaN/p-AlGaN hybrid nanorod arrays. The enhancement mechanism involves directly reflecting the transverse electric (TE) mode within the escape cone at the p-AlGaN/Al mirror interface, thereby minimizing absorption by p-GaN. Simultaneously, TE and transverse magnetic (TM) modes outside the escape cone are scattered by the nanorods and redirected into the escape cone, promoting forward emission. 3D finite-difference time-domain simulations predict a 79% increase in LEE for TM and a 187% improvement for TE. Experimentally, we observe a 140% enhancement in peak light output power (LOP), a 148% boost in external quantum efficiency (EQE), and a 146% increase in wall-plug efficiency (WPE) at 1 mA compared to planar designs. This innovative approach markedly advances the performance of DUV micro-LEDs, fostering new possibilities in high-efficiency DUV technologies.
31 December 2015 in Journal of Vacuum Science & Technology B
In this work, the authors report the incorporation of TiW alloy in InGaN/GaN-based flip-chip light-emitting diodes (LEDs). The advantages provided by the use of TiW are analyzed in detail. InGaN/GaN multiple quantum well LEDs with a Ni/Ag/TiW metal stack are found to tolerate high-temperature annealing better than those with a Ni/Ag metal stack. Highly improved current–voltage characteristics and enhanced optical output power are achieved for the devices with a TiW thin layer. These changes are ascribed to the higher reflectivity, smoother surface, and better ohmic properties of the device containing TiW after annealing. Better heat management of the device with TiW is demonstrated by comparing electroluminescence spectra of the two device structures. Overall, these factors resulted in devices with TiW exhibiting a higher external quantum efficiency than devices without TiW. Detailed x-ray photoelectron spectroscopy analyses of the reflector metal stacks reveal little intermixing of the layers after annealing in the devices with TiW. The results show that incorporation of TiW is a promising approach for the fabrication of high-performance InGaN/GaN flip-chip LEDs.
14 October 2024 in Journal of Physics D: Applied Physics
In this study, 236 nm AlGaN-based deep ultraviolet (DUV) micro-LEDs with different sized P-contact areas are designed and fabricated, and the sidewalls are restored by a wet chemical treatment method with KOH solution. The results reveal that proper KOH treatment can effectively remove plasma damaged materials and clearly show the formation of m-plane facets. Compared with untreated micro-LEDs, the reverse leakage current of the treated micro-LEDs under −10 V decreases by up to 91.7% and the specific contact resistivity (SCR) reduces from 6.94 Ω cm2 to 0.07 Ω cm2. The underlying mechanism is that the KOH treatment removes the sidewall defects which lead to surface nonradiative recombination sites and surface leakage. Moreover, KOH treatment also removes contamination on the P+-GaN surface and leads to lower SCR. However, a much longer treatment also destructs the 20 nm P+-GaN layer, which results in higher voltage but less DUV light absorption. As a result, the peak light output power density increases from 2.12 W cm−2 to 4.01 W cm−2, representing an 89.2% increase. Efficient enhancement of micro-LEDs is anticipated to facilitate the development of DUV micro-LEDs for maskless lithography and high-capacity DUV non-line-of-sight communication.