The current research designed a statistical model for the bobbin tool friction stir processing (BT-FSP) of AA1050 aluminum alloy using the Response Surface Method (RSM). The analysis studied the influence of tool travel speeds of 100, 200, and 300 mm/min and different pin geometries (triangle, square, and cylindrical) at a constant tool rotation speed (RS) of 600 rpm on processing 8 mm thickness AA1050. The developed mathematical model optimizes the effect of the applied BT-FSP parameters on machine torque, processing zone (PZ) temperature, surface roughness, hardness values, and ultimate tensile strength (UTS). The experimental design is based on the Face Central Composite Design (FCCD), using linear and quadratic polynomial equations to develop the mathematical models. The results show that the proposed model adequately predicts the responses within the processing parameters, and the pin geometry is the most influential parameter during the BT-FSP of AA1050. The analysis of variance exhibit that the developed mathematical models can effectively predict the values of the machine torque, PZ temperature, surface roughness, hardness, and UTS with a confidence level of over 95% for the AA1050 BT-FSP. The optimization process shows that the optimum parameters to attain the highest mechanical properties in terms of hardness and tensile strength at the lowest surface roughness and machine torque are travel speed (TS) of 200 mm/min using cylindrical (Cy) pin geometry at the constant RS of 600 rpm. The PZ temperature of the processed specimens decreased with increasing TS at different pin geometries. Meanwhile, the surface roughness of the processed passes and machine torque increased with increasing the TS at different pin geometries. Increasing TS from 100 to 300 mm/min increases the hardness values of the processed materials using different pin geometries. The highest UTS of 79 MPa for the processed specimens was attained at the TS of 200 mm/min and RS of 600 rpm using the Cy pin geometry.

Owing to their exceptional mechanical properties, the various welding wires used to combine aluminum can meet the needs of many engineering applications that call for components with both good mechanical and lightweight capabilities. This study aims to produce high-quality welds made of AA7075 aluminum alloy using the GTAW technique and various welding wires, such as ER5356, ER4043, and ER4047. The microstructure, macrohardness, and other mechanical characteristics, such as tensile strength and impact toughness, were analyzed experimentally. To check the fracture surface of the AA7075 welded joints, the specimens were examined using optical and scanning electron microscopy (SEM). A close examination of the samples that were welded with ER5356 welding wire revealed a fine grain in the weld zone (WZ). In addition, the WZ of the ER4043 and ER4047 welded samples had a coarse grain structure. Because the hardness values of the welded samples were lower in the WZ than in the base metal (BM) and heat-affected zone (HAZ), the joints filled with ER5356 welding wire provided the highest hardness values compared to other filler metals. Additionally, the ER4047 filler metal yielded the lowest hardness in the weld zone. The welding wire of ER5356 produced the greatest results for ultimate tensile stress, yield stress, welding efficiency, and strain-hardening capacity (Hc), whereas the filler metal of ER4043 produced the highest percentage of elongation. In addition, the ER4047 fracture surface morphology revealed coarser and deeper dimples than the ER5356 fine dimples in the welded joints. Finally, the highest impact toughness was obtained at joints filled with the ER4047 filler metal, whereas the lowest impact toughness was obtained at the BM.

This study investigates the impact of different filler wires (ER5356, ER4043, and ER4047) on the microstructural and mechanical properties of EN AW-6082 Al alloy joints produced by tungsten inert gas (TIG) welding. Butt-welded samples with a single V-groove joint configuration were prepared using optimized welding parameters. The welded samples were subjected to visual inspection, microstructural analysis, hardness testing, tensile testing, and impact toughness evaluation. The results showed that all the welds were free of visible defects. Microstructural examination revealed that the ER5356 filler produced the finest grain structure of 18.03 ± 3 μm, while ER4047 resulted in the coarsest grains of 36.07 ± 5 μm. Correspondingly, the joints made with ER5356 exhibited the highest tensile stress of 278 ± 6 MPa, yield stress of 219 ± 5.4 MPa, hardness values of 72.7 ± 5 HV, and welding efficiency of 86.07%, whereas those made with ER4047 produced the lowest values. The hardness in the weld region was lower than that in the parent metal and heat-affected zone for all samples. However, ER4047 welds demonstrated superior impact toughness and strain-hardening capacity. The findings underscore the importance of filler metal selection in tailoring mechanical properties for high-performance applications.

Understanding and optimizing the relationship between critical processing parameters (rotational speed and dwell time) and the resulting weld performance is crucial for the effective application of friction stir spot welding (FSSW) in joining aluminum alloys. FSSW is an increasingly important solid-state, clean technology alternative for joining lightweight alloys such as AA5052-H32 in various industries. To optimize this technique for lap joint configurations, the current study examines the influence of rotational speeds (500, 1000, and 1500 rpm) and dwell times (1, 2, and 3 s) on the heat input energy, hardness across weld zones, and tensile/shear load, using a full factorial Design-Expert (DOE) analysis. The FSSW responses of the numerical model were validated using the experimental results for the spot-welded joints. The findings indicate that the dwell time significantly affected the mechanical properties, while the tool rotational speed had a substantial effect on the heat input energy and mechanical properties. Fracture surfaces predominantly exhibited ductile failure with diverse dimple morphologies, consistent with the enhanced tensile properties under optimal parameters. The presence of finer dimples suggests a mixed-mode fracture involving shear.