Dora Janovszky

Dr. Dora Janovszky

University of Miskolc, Miskolc, Hungary
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 September 2021 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
DJDora Janovszky
Dora Janovszky
MSMaria Sveda
Maria Sveda
ASAnna Sycheva
Anna Sycheva
FKFerenc Kristaly
Ferenc Kristaly
FZFerenc Zámborszky
Ferenc Zámborszky
GKGeorge Kaptay
George Kaptay
A remarkable number of scientific papers are available in the literature about the bulk amorphous alloys and metallic glasses. Today, DSC is an essential tool for amorphous alloys research and development, and of course for quality assurance. In many cases, users seek to examine the determination of only one or two properties, although much more information can be obtained from the measurements. The research involved structural relaxation, Curie temperature, glass temperature, crystallization, phase separation, nanocrystalline volume fraction, melting point and liquidus temperature determination subjects and kinetics of microstructural transformations induced by thermal treatment. We collected and present the information that can be obtained with this technique and draws the reader’s attention to some potential problems related to data interpretation.

1 February 2016 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
ICI. Cora
I. Cora
PPP. Pekker
P. Pekker
IDI. Dódony
I. Dódony
DJDora Janovszky
Dora Janovszky

14 July 2012 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
DJDora Janovszky
Dora Janovszky
KTK. Tomolya
K. Tomolya
ASA. Sycheva
A. Sycheva
GKGeorge Kaptay
George Kaptay

12 November 2012 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
GKG. Kőrösy
G. Kőrösy
KTKinga Tomolya
Kinga Tomolya
DJDora Janovszky
Dora Janovszky
JSJenő Sólyom
Jenő Sólyom
There is an active research work in the field of amorphous alloys since the discovery of metallic glasses, half a century ago [. In contrast with crystalline alloys, amorphous one have unique material properties, e.g. high yield strength, superior elastic limit, high corrosion resistance, unique acoustical properties [2,. Producing amorphous alloys, it is first necessary to quantify the forming of structure and define the amorphous amount. All of the methods to determine the structure have advantages and disadvantages. An accurate determination of amorphous volume fraction can be accomplished by transmission electron microscopy (TEM), this observation is much localized [ and the evaluation is difficult. The most common techniques to determine the amorphous fraction are XRD and DSC methods, which reflect the entire sample [. However, XRD has a detection limit depending on the type of equipment. Apart from this fact, it is an admitted method in researches, if the XRD reflexion shows an amorphous halo. Amorphous fraction transformed to crystalline can be measured by DSC. This method is much sensitive to impurities, especially oxygen, which can influence on the results.

25 September 2012 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
KTK. Tomolya
K. Tomolya
DJDora Janovszky
Dora Janovszky
TJT. Janvari
T. Janvari
ASA. Sycheva
A. Sycheva
FTF. Tranta
F. Tranta
ARA. Roosz
A. Roosz

21 April 2019 in Materials
Verified
Journal Article
Open access
PDF file
DJDora Janovszky
Dora Janovszky
Pure Al particles reinforced with amorphous-nanocrystalline Cu36Zr48Ag8Al8 particles composite powders were prepared by high-energy milling without and with ethanol. The mechanical milling procedures were compared so that in the case of dry milling the particle size increased owing to cold welding, but the crystallite size decreased below 113 nm. The amorphous phase disappeared and was not developed until 30 h of milling time. Using ethanol as a process control agent, the particle size did not increase, while the amorphous fraction increased to 15 wt.%. Ethanol decomposed to carbon dioxide, water, and ethane. Its addition was necessary to increase the amount of the amorphous structure.