The paper presents a new insight into understanding a mechanism to trigger the Crow and Champagne preferred mode. It is shown on the basis of numerical simulations that the preferred mode is established as a result of nonlinear interactions of primary structures generated by the Kelvin–Helmholtz instability. These interactions form larger coherent vortices characterized with frequency equal to half of the frequency of the primary perturbation. The paper shows that the shear-layer thickness at the nozzle exit constitutes a key parameter that influences significantly the jet response to an external forcing. The simulations were performed for jets with different shear-layer thicknesses. For the thicker shear layer the classical Kelvin–Helmholtz instability is observed. In this case the jet response to an external varicose forcing seems to be very similar to the experimental results of Crow and Champagne. The results presented shed new light on the preferred mode and the frequency selection mechanism confirming the suggestion of Crow and Champagne that nonlinearity is responsible for the preferred frequency. Significantly different results were obtained for a jet characterized by a thin shear layer. In this case the jet could be introduced into a self-sustained regime. External forcing with a frequency equal to the frequency of the natural self-sustained mode or with its subharmonic has practically no effect on the jet dynamics. The jet response to the forcing with frequencies different from the natural one depends on the forcing amplitude. A weak forcing disturbs the self-sustained mode leading to an interaction of two different modes that is observed in spectra with many frequencies related to both the self-sustained mode and the oscillations triggered by forcing. A stronger forcing suppresses the self-sustained mode and only the frequency components related to the stimulation are observed in the spectra. A mechanism responsible for the jet response to an external forcing under the self-sustained regime has not been extensively studied so far and a full understanding of these phenomena needs further studies and careful analysis.
The paper presents a detailed LES analysis of turbulent round jets dominated by the mechanism of Kelvin-Helmholtz (K-H) instability and the so-called self-sustained regime, which is characterised by large velocity fluctuations, reminiscent of the behaviour of excited jets. It is shown that the occurrence of this regime is largely conditioned by the type and parameters of the inlet jet velocity profile, i.e., the shear layer momentum thickness ????, turbulence intensity Ti. A high order numerical code based on the combined pseudo-spectral / compact difference methods is used in the simulations. Analysis is performed for the Reynolds number Re = 1 × 104 with ???? characterised by R/???? = 16, 20, 24, 28 and 32 (with R - jet radius) and for Ti = 10−2, 10−3, 10−4. Two inlet velocity profiles are used in the simulations: hyperbolic tangent and Blasius. Comparisons focus on the axial velocity profiles and the spectra of the velocity signals. It is shown that in the self-sustained regime the results obtained with the Blasius profile are significantly closer to the experimental data. Sensitivity tests of the self-sustained regime on the sub-grid modelling are performed based on four well known models: classical and dynamic Smagorinsky, the filtered structure function model of Ducros et al. (JFM, 1996) and the relatively new model proposed by Vreman (PoF, 2004). It is shown that in the case of the classical Smagorinsky model an excess of sub-grid dissipation prevents the appearance of self-sustained velocity oscillations and in effect gives results significantly different from the remaining models. On the other hand, when the jets are dominated by K-H instability all the models lead to very similar solutions.
The paper presents a novel view on the absolute instability phenomenon in heated variable density round jets. As known from literature the global instability mechanism in low density jets is released when the density ratio is lower than a certain critical value. The existence of the global modes was confirmed by an experimental evidence in both hot and air-helium jets. However, some differences in both globally unstable flows were observed concerning, among others, a level of the critical density ratio. The research is performed using the Large Eddy Simulation (LES) method with a high-order numerical code. An analysis of the LES results revealed that the inlet conditions for the velocity and density distributions at the nozzle exit influence significantly the critical density ratio and the global mode frequency. Two inlet velocity profiles were analyzed, i.e., the hyperbolic tangent and the Blasius profiles. It was shown that using the Blasius velocity profile and the uniform density distribution led to a significantly better agreement with the universal scaling law for global mode frequency.
2 May 2017 in International Journal of Numerical Methods for Heat & Fluid Flow
Purpose: The purpose of the paper is to summarize recent achievements and suggest further research directions in numerical studies of round free jets with particular attention on the influence of the inlet parameters (mean velocity, turbulence intensity, length and time scales) on the jet dynamics. Design/methodology/approach: The large eddy simulation (LES) and direct numerical simulation (DNS) are regarded as accurate tools which can support expensive and requiring sophisticated measurements techniques experimental studies. In the paper, the authors present challenges and recent findings related to the LES and DNS of jet type flows in isothermal, heated, excited and reactive conditions. Findings: LES of the isothermal jet allowed to identify the new jet instability mechanism leading to the self-sustained oscillations and to determine conditions required to trigger this phenomenon. Numerical simulation on the low-density round jet captured the phenomenon of absolute instability with a very good agreement with the experimental findings. LES/DNS of excited jet exhibited bifurcating and blooming jet and showed that the jet can be directly controlled by excitation frequency what is crucial issue also for flame shape control. Originality/value: The paper shows complexity of seemingly simple jet type flow and proves that despite a huge interest in these flows and relatively deep knowledge on the jet dynamics there are still some open issues requiring further studies.
31 May 2023 in International Journal of Heat and Mass Transfer
In this study, we employ the potential of the global instability phenomenon to qualitatively alter the dynamics of a turbulent flame. We adopt the large eddy simulation method and an in-house numerical code. For the combustion process we do not include explicit sub-filter modeling. The accuracy of this ‘no combustion model’ approach is verified by comparison against the Eulerian Stochastic Fields method. We include several test cases representing different flow regimes, including convective and absolutely unstable conditions. The focus is on a counter-current configuration, which includes a central jet nozzle supplying hydrogen fuel surrounded by a somewhat larger co-axial nozzle sucking fluid from the surroundings of the central nozzle. The suction generates a counterflow where global instability is found to be triggered if sufficiently strong suction is applied. The critical suction value $$I_{GI}$$ is larger if the level of the inlet turbulence intensity $$T_i$$ is increased. Depending on the suction strength, the flame quickly stabilizes, either as being attached to the nozzle or as a lifted flame hovering at a height of a few fuel nozzle diameters. Additionally, it is shown that increasing $$T_i$$ can assist an initially lifted flame to attach to the nozzle. Flame lifting is the result of self-induced strong toroidal vortices that lead to leaner combustion conditions of the mixture upstream of the flame base. The toroidal vortices prevent upstream flame propagation and lead to a very intense mixing process that gives rise to the lifted reaction zone. This ensures almost complete fuel combustion at a short distance from the inlet. On the contrary, when the suction strength is below $$I_{GI}$$ , the flames are attached and a high temperature near the fuel inlet causes an increase in molecular viscosity. This tends to laminarize the mixing layer between the fuel and oxidizer. The flames appear as if they were laminar and non-premixed over a long distance from the inlet. In such a situation, a significant amount of fuel remains unburned.