In the present study, 5-fluorouracil-loaded niosomal nanoparticles were successfully prepared and coated with chitosan and subsequently crosslinked by tripolyphosphate to form niosomal nanogels. The prepared niosomal formulations were fully characterized for their particle size, zeta potential, particle morphology, drug entrapment efficiency, and in vitro drug release profile. The prepared niosomal nanocarriers exhibited nanoscale particle sizes of 165.35 ± 2.75-322.85 ± 2.75 nm. Chitosan-coated and TPP-crosslinked niosomes exhibited a slightly decreased in particle size and a switch of zeta potential from negative to positive values. In addition, high yield percentage, drug encapsulation efficiency, and drug loading values of 92.11 ± 2.07 %, 66.59 ± 6.06, and 4.65 ± 0.5 were obtained for chitosan-coated formulations, respectively. Moreover, lowering the rate of 5-FU in vitro release was achieved within 72 h by using chitosan-coated formulations. All prepared formulations revealed hemocompatible properties in hemolysis assay with less than 5 % hemolysis percentage at their higher possible concentrations (500 µM and 1 mM). The cell viability by MTT assay showed higher anticancer activity against B16F10 cancerous cells and lower cytotoxicity toward NIH3T3 normal cells than control and pure 5-FU in the studied concentration range (10-100 µM). Investigating the cell migration inhibition properties of fabricated formulations revealed similar results with in vitro cell viability assay with a higher migration inhibition rate for B16F10 cells than NIH3T3 cells, controls, and free 5-FU.
The pervasiveness of fungal infections is an issue for skin health globally, and there are a reported 40 million cases in developed and developing countries. Novel drug delivery systems provide better therapeutic efficacy over conventional drug therapy due to their lower side effects and toxicity. Furthermore, combinations of essential oils can represent alternative therapies for fungal infections that are resistant to synthetic drugs. This study is aimed at developing Timur oil into a nanoemulgel and evaluating its antifungal effects. The development of the formulation involved the preparation of a nanoemulsion by the titration method, followed by its evaluation for various physicochemical properties. The antifungal activity of the nanoemulgel against Candida albicans was evaluated. The zone of inhibition was determined using the disk diffusion method. The results show that the developed nanoemulgel has a particle size of 139 ± 6.11 nm, a PDI of 0.309, and a zeta potential of −19.12 ± 2.73 mV. An in vitro drug release study showed a sustained release of 70 ± 0.289% of the drug over a period of 24 h. The % drug permeation across the skin was found to be 79.11 ± 0.319% over 24 h. However, the amount of drug retained in the skin was 56.45 µg/g. The flux for the nanoemulgel was found to be 94.947 µg/cm2/h, indicating a better permeability profile. The nanoemulgel formulation showed a zone of inhibition of 15 ± 2.45 mm, whereas the 1% ketoconazole cream (marketed preparation) exhibited a zone of inhibition of 13 ± 2.13 mm. The results of this study suggest that developed nanoemulgel containing Timur oil and rosemary oil has the potential to be used for treating topical fungal infections caused by Candida albicans.
The aim of the work is to consolidate azilsartan-kamedoxomil (AZM) into lipid matrix controlled-release microparticles to enhance its permeability because AZM belongs to Biopharmaceutical classification (BCS) IV which characterized by poor permeability and to protect AZM from light and humidity and execute a prolonged release profile. Materials and methods. A reversed-phase HPLC method was created and validated to estimate the drug. AZM microparticles formulations were invented using melt dispersion technique and waxy materials such as carnuba wax, beeswax, stearic acid in the ratio of waxy-substance: drug ranging from 0.25: 1 to 1:1 and stabilizer namely; tween 80 and Poloxamer 407 in ratio of stabilizer: drug ranging from 0.5:1 to 1:1. Azilsartan formulations were assessed for azilsartan-medoxomil content, loading, entrapment efficiency, the zeta potential,the particle size, the morphology by scanning electronic microscopy (SEM), and in-vitro release profile. Results. Zeta potential results for microparticle formulations using beeswax and carnuba range from -21.1 mV to -26.6 mV and -20.6 mV to -26.7 mV, respectively. This difference indicates that the azilsartan microparticles containing stearic acid are better stabilized with zeta potential of 25.3 - 29.7 mV. Furthermore, the release from azilsartan microparticle formulations containing stearic acid exceeded 80 % after 8 h and remained for 24 h while release from beeswax did not exceed 65 % after the same period and less than 60 % in case of carnuba formulations Conclusions. The formulation (AZSP4) exhibited the highest zeta potential and released exceeding 80 % of AZM over the course of 8 hours and remained over a day. AZSP4 microparticles formulation containing, poloxamer 407, in a 0.8:0.8:1 drug: stearic acid: poloxamer ratio proved the ability of stearic acid microencapsulation employing poloxamer as stabilizer in a certain ratio can prolong the release of AZM
20 February 2023 in Journal of Pharmaceutical Innovation
In this study, different formulas (F1-F7) containing 4 mg of 5-fluorouracil (5-FU) were prepared as a tablet in form of CPOP-CT. The core of these formulas contained citric acid, sodium chloride, LMCh, MMCh, ProSolv SMCC®90 and magnesium stearate mixed with 5-FU. The formulas were double coated by an inner layer containing chitosan and PEG-400 and outer layer as an enteric coating containing Eudragit®L100-55, triethyl citrate and talc. The solubility of 5-FU in different dissolution media (pH 5, pH 7) was studied. The results indicated increase of LMCh and decrease of citric acid lead to slow the release of 5-FU for F1, F2, F3, F4, F5, F6 and F7 in simulated colonic fluid with 61%, 29%, 32%, 43%, 52%, 39% and 68%, respectively within 21 h. In addition, the release rate of 5-FU was affected by changing the weight gain percentages of semipermeable CAM. 6% and 10% weight gains of F3 released 5-FU completely within times (t100% ) of 46 h and 65 h, respectively which are acceptable with colonic transit time (78 h) compared with 14% weight gain (t100% = 135 h). In SCF, the enzymatic effect on the release of 5-FU within 21 h for F6 was studied which synthetic almond emulsin β-glucosidase and human fecal enzyme increased release of 5-FU with 26% and 39%, respectively compared to 18% release with no enzyme. Degradation effect of these enzymes made pores in semipermeable to release drugs and then modulate the drug kinetic from zero order into first order.