Incorporating additives into organic halide perovskite solar cells is the typical approach to improve power conversion efficiency. In this paper, a methyl-ammonium lead iodide (CH3NH3PbI3, MAPbI3) organic perovskite film was fabricated using a two-step sequential process on top of the poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) hole-transporting layer. Experimentally, water and potassium halides (KCl, KBr, and KI) were incorporated into the PbI2 precursor solution. With only 2 vol% water, the cell efficiency was effectively improved. Without water, the addition of all of the three potassium halides unanimously degraded the performance of the solar cells, although the crystallinity was improved. Co-doping with KI and water showed a pronounced improvement in crystallinity and the elimination of carrier traps, yielding a power conversion efficiency (PCE) of 13.9%, which was approximately 60% higher than the pristine reference cell. The effect of metal halide and water co-doping in the PbI2 layer on the performance of organic perovskite solar cells was studied. Raman and Fourier transform infrared spectroscopies indicated that a PbI2-dimethylformamide-water related adduct was formed upon co-doping. Photoluminescence enhancement was observed due to the co-doping of KI and water, indicating the defect density was reduced. Finally, the co-doping process was recommended for developing high-performance organic halide perovskite solar cells.
Perovskite solar cells have been proven to enhance cell characteristics by introducing passivation materials that suppress defect formation. Defect states between the electron transport layer and the absorption layer reduce electron extraction and carrier transport capabilities, leading to a significant decline in device performance and stability, as well as an increased probability of non-radiative recombination. This study proposes the use of an amino acid (L-Histidine) self-assembled monolayer material between the transport layer and the perovskite absorption layer. Surface analysis revealed that the introduction of L-Histidine improved both the uniformity and roughness of the perovskite film surface. X-ray photoelectron spectroscopic analysis showed a reduction in oxygen vacancies in the lattice and an increase in Ti4+, indicating that L-Histidine successfully passivated trap states at the perovskite and TiO2 electron transport layer interface. In terms of device performance, the introduction of L-Histidine significantly improved the fill factor (FF) because the reduction in interface defects could suppress charge accumulation and reduce device hysteresis. The FF of large-area solar modules (25 cm2) with L-Histidine increased from 55% to 73%, and the power conversion efficiency (PCE) reached 16.5%. After 500 h of aging tests, the PCE still maintained 91% of its original efficiency. This study demonstrates the significant impact of L-Histidine on transport properties and showcases its potential for application in the development of large-area perovskite module processes.
Perovskite solar cells are among the most promising renewable energy devices, and enhancing their stability is crucial for commercialization. This research presents the use of L-Ergothioneine (L-EGT) as a passivation material in perovskite solar cells, strategically placed between the electron transport layer and the perovskite absorber layer to mitigate defect states at the heterojunction interface. Surface analysis reveals that introducing L-EGT passivation material significantly improves the quality of the perovskite film. X-ray diffraction analysis indicates that L-EGT slows down perovskite film degradation and successfully suppresses secondary phase formation. X-ray photoelectron spectroscopic analysis shows that oxygen vacancies in the lattice decrease from 29.21% to 15.81%, while Ti4+ content increases from 70.75% to 79.15%, suggesting that L-EGT effectively passivates trap states at the interface between perovskite and TiO2 electron transport layer. The reduction of defects at the interface inhibits charge accumulation and lowers the device’s internal series resistance, leading to improved overall performance. The study finds that the introduction of L-EGT significantly improves the fill factor and efficiency, with the power conversion efficiency (PCE) rising from 16.88% to 17.84%. After 720 h of aging, the PCE retains approximately 91%. The results demonstrate the significant impact of the amino acid L-EGT passivation material in suppressing interfacial defects and greatly improving the long-term stability of perovskite devices.