High-entropy alloys (HEAs) provide new research avenues for alloy combinations in the periodic table, opening numerous possibilities in novel-alloy applications. However, their electrical characteristics have been relatively underexplored. The challenge in establishing an HEA electrical conductivity model lies in the changes in electronic characteristics caused by lattice distortion and complexity of nanostructures. Here we show a low-frequency electrical conductivity model for the Nb-Mo-Ta-W HEA system. The cocktail effect is found to explain trends in electrical-conductivity changes in HEAs, while the magnitude of the reduction is understood by the calculated plasma frequency, free electron density, and measured relaxation time by terahertz spectroscopy. As a result, the refractory HEA Nb15Mo35Ta15W35 thin film exhibits both high hardness and excellent conductivity. This combination of Nb15Mo35Ta15W35 makes it suitable for applications in atomic force microscopy probe coating, significantly improving their wear resistance and atomic-scale image resolution.
Perovskite solar cells have been proven to enhance cell characteristics by introducing passivation materials that suppress defect formation. Defect states between the electron transport layer and the absorption layer reduce electron extraction and carrier transport capabilities, leading to a significant decline in device performance and stability, as well as an increased probability of non-radiative recombination. This study proposes the use of an amino acid (L-Histidine) self-assembled monolayer material between the transport layer and the perovskite absorption layer. Surface analysis revealed that the introduction of L-Histidine improved both the uniformity and roughness of the perovskite film surface. X-ray photoelectron spectroscopic analysis showed a reduction in oxygen vacancies in the lattice and an increase in Ti4+, indicating that L-Histidine successfully passivated trap states at the perovskite and TiO2 electron transport layer interface. In terms of device performance, the introduction of L-Histidine significantly improved the fill factor (FF) because the reduction in interface defects could suppress charge accumulation and reduce device hysteresis. The FF of large-area solar modules (25 cm2) with L-Histidine increased from 55% to 73%, and the power conversion efficiency (PCE) reached 16.5%. After 500 h of aging tests, the PCE still maintained 91% of its original efficiency. This study demonstrates the significant impact of L-Histidine on transport properties and showcases its potential for application in the development of large-area perovskite module processes.
Perovskite solar cells are among the most promising renewable energy devices, and enhancing their stability is crucial for commercialization. This research presents the use of L-Ergothioneine (L-EGT) as a passivation material in perovskite solar cells, strategically placed between the electron transport layer and the perovskite absorber layer to mitigate defect states at the heterojunction interface. Surface analysis reveals that introducing L-EGT passivation material significantly improves the quality of the perovskite film. X-ray diffraction analysis indicates that L-EGT slows down perovskite film degradation and successfully suppresses secondary phase formation. X-ray photoelectron spectroscopic analysis shows that oxygen vacancies in the lattice decrease from 29.21% to 15.81%, while Ti4+ content increases from 70.75% to 79.15%, suggesting that L-EGT effectively passivates trap states at the interface between perovskite and TiO2 electron transport layer. The reduction of defects at the interface inhibits charge accumulation and lowers the device’s internal series resistance, leading to improved overall performance. The study finds that the introduction of L-EGT significantly improves the fill factor and efficiency, with the power conversion efficiency (PCE) rising from 16.88% to 17.84%. After 720 h of aging, the PCE retains approximately 91%. The results demonstrate the significant impact of the amino acid L-EGT passivation material in suppressing interfacial defects and greatly improving the long-term stability of perovskite devices.
Calcium titanium oxide has emerged as a highly promising material for optoelectronic devices, with recent studies suggesting its potential for favorable thermoelectric properties. However, current experimental observations indicate a low thermoelectric performance, with a significant gap between these observations and theoretical predictions. Therefore, this study employs a combined approach of experiments and simulations to thoroughly investigate the impact of structural and directional differences on the thermoelectric properties of two-dimensional (2D) and three-dimensional (3D) metal halide perovskites. Two-dimensional (2D) and three-dimensional (3D) metal halide perovskites constitute the focus of examination in this study, where an in-depth exploration of their thermoelectric properties is conducted via a comprehensive methodology incorporating simulations and experimental analyses. The non-equilibrium molecular dynamics simulation (NEMD) was utilized to calculate the thermal conductivity of the perovskite material. Thermal conductivities along both in-plane and out-plane directions of 2D perovskite were computed. The NEMD simulation results show that the thermal conductivity of the 3D perovskite is approximately 0.443 W/mK, while the thermal conductivities of the parallel and vertical oriented 2D perovskites increase with n and range from 0.158 W/mK to 0.215 W/mK and 0.289 W/mK to 0.309 W/mK, respectively. Hence, the thermal conductivity of the 2D perovskites is noticeably lower than the 3D ones. Furthermore, the parallel oriented 2D perovskites exhibit more effective blocking of heat transfer behavior than the perpendicular oriented ones. The experimental results reveal that the Seebeck coefficient of the 2D perovskites reaches 3.79 × 102 µV/K. However, the electrical conductivity of the 2D perovskites is only 4.55 × 10−5 S/cm, which is one order of magnitude lower than that of the 3D perovskites. Consequently, the calculated thermoelectric figure of merit for the 2D perovskites is approximately 1.41 × 10−7, slightly lower than that of the 3D perovskites.
We investigated the optical constants of thin films of the Nb25Mo25Ta25W25 alloy, which belongs to high-entropy alloys (HEAs), with a transmission terahertz (THz) measurement system and discovered that the refractive index, extinction coefficient, and conductivity of the HEA thin film measured in the range of 0.3–1.0 THz all increased as the thickness of the thin film increased (the thickness was maintained in the range between 10 and 40 nm). According to the experimental results, this alloy with a high refractive index is suitable for producing high-contrast gratings (HCGs). The principle behind achieving a high contrast with a high-reflection HEA grating is to harness the confined plasmonic energy within the grating, thereby enhancing the localized plasmonic energy within the grating. This work elucidates that we can not only fabricate THz components by controlling the thickness of the thin film but also utilize the high refractive index of this material to create HCGs.