Vertically oriented, self-organized TiO₂–MnO₂ nanotube arrays were successfully obtained by one-step anodic oxidation of Ti–Mn alloys in an ethylene glycol-based electrolyte. The as-prepared samples were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), UV-Vis absorption, photoluminescence spectroscopy, X-ray diffraction (XRD), and micro-Raman spectroscopy. The effect of the applied potential (30–50 V), manganese content in the alloy (5–15 wt. %) and water content in the electrolyte (2–10 vol. %) on the morphology and photocatalytic properties was investigated for the first time. The photoactivity was assessed in the toluene removal reaction under visible light, using low-powered LEDs as an irradiation source (λ_max = 465 nm). Morphology analysis showed that samples consisted of auto-aligned nanotubes over the surface of the alloy, their dimensions were: diameter = 76–118 nm, length = 1.0–3.4 μm and wall thickness = 8–11 nm. It was found that the increase in the applied potential led to increase the dimensions while the increase in the content of manganese in the alloy brought to shorter nanotubes. Notably, all samples were photoactive under the influence of visible light and the highest degradation achieved after 60 min of irradiation was 43%. The excitation mechanism of TiO₂–MnO₂ NTs under visible light was presented, pointing out the importance of MnO₂ species for the generation of e⁻ and h⁺.

V₂O₅-TiO₂ mixed oxide nanotube (NT) layers were successfully prepared via the one-step anodization of Ti-V alloys. The obtained samples were characterized by scanning electron microscopy (SEM), UV-Vis absorption, photoluminescence spectroscopy, energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (DRX), and micro-Raman spectroscopy. The effect of the applied voltage (30–50 V), vanadium content (5–15 wt %) in the alloy, and water content (2–10 vol %) in an ethylene glycol-based electrolyte was studied systematically to determine their influence on the morphology, and for the first-time, on the photocatalytic properties of these nanomaterials. The morphology of the samples varied from sponge-like to highly-organized nanotubular structures. The vanadium content in the alloy was found to have the highest influence on the morphology and the sample with the lowest vanadium content (5 wt %) exhibited the best auto-alignment and self-organization (length = 1 μm, diameter = 86 nm and wall thickness = 11 nm). Additionally, a probable growth mechanism of V₂O₅-TiO₂ nanotubes (NTs) over the Ti-V alloys was presented. Toluene, in the gas phase, was effectively removed through photodegradation under visible light (LEDs, λ_max = 465 nm) in the presence of the modified TiO₂ nanostructures. The highest degradation value was 35% after 60 min of irradiation. V₂O₅ species were ascribed as the main structures responsible for the generation of photoactive e⁻ and h⁺ under Vis light and a possible excitation mechanism was proposed.

Plasmonic nanoparticles are widely recognized as photothermal conversion agents, i.e., nanotransducers or nanoheaters. Translation of these materials into practical applications requires quantitative analyses of their photothermal conversion efficiencies (η). However, the value of η obtained for different materials is dramatically influenced by the experimental setup and method of calculation. Here, we evaluate the most common methods for estimating η (Roper's and Wang's) and compare these with numerical estimates using the simulation software ANSYS. Experiments were performed with colloidal gold nanorod solutions suspended in a hanging droplet irradiated by an 808 nm diode laser and monitored by a thermal camera. The ANSYS simulations accounted for both heating and evaporation, providing η values consistent with the Wang method but higher than the Roper approach. This study details methods for estimating the photothermal efficiency and finds ANSYS to be a robust tool where experimental constraints complicate traditional methods.

To gain insights into how the presence of the second metal in Ti alloys affects the morphology, crystallinity, chemical structure, and photocatalytic/photoelectrochemical activity of mixed-oxide nanotubes (TiO₂–M_xO_y), five systems were electrochemically synthesized in a fluoride-containing ethylene glycol-based electrolyte by using Ti alloys, with 10 wt % of the second metal, as precursors. The level of self-organization and -orientation in the obtained samples followed the order: Ag < Cu < Mn < V < Co, being the Ti₉₀Ag₁₀_40V sample, the only presenting single Ag nanoparticles embedded in the oxide layer. The highest photocatalytic and photoelectrochemical activities were reported for the Ti₉₀Ag₁₀_40V sample, which can be attained to the heterojunction between the oxides, the formation of single Ag nanoparticles, and the high level of self-organization. Apparently, the intrinsic heterojunction between the oxides depends on the still-needed-to-be-estimated stability of the oxides produced during the anodization of each system.

Current HER2-targeted therapies including monoclonal antibodies, antibody-drug conjugates (ADCs) and small-molecule tyrosine kinase inhibitors face limitations such as hepatotoxicity, development of treatment resistance, and subsequent disease relapse. To overcome these challenges, this study combines the specificity of a HER2-targeting affibody molecule (Z_HER2:2891-Cys) with the photothermal properties of gold nanorods (AuNRs), forming bioconjugates (Affi–AuNRs) for selective treatment of HER2-positive cancer cells. Affi–AuNRs were fabricated via a two-step surface modification: (i) ligand exchange to displace cetyltrimethylammonium bromide (CTAB) with poly(ethylene glycol) methyl ether thiol (mPEG-SH), and (ii) covalent attachment of the affibody molecule via Au–S chemistry. Affi-AuNRs exhibited a photothermal conversion efficiency of 64 ± 5%, comparable to that of CTAB-stabilized AuNRs (59 ± 4%). Confocal microscopy confirmed that Affi-AuNRs are selectively internalized by HER2-positive SKOV-3 cells, with minimal uptake by HEK293T cells, which have low HER2 expression. Upon exposure to 808 nm near-infrared (NIR) LED irradiation (408 mW cm^–2, 15 min), Affi-AuNRs significantly reduced SKOV-3 cell viability by 85 ± 9% (p < 0.001) relative to untreated controls with no detectable cytotoxicity in HEK293T cells. These results demonstrate HER2-selective photothermal cytotoxicity mediated by Affi–AuNRs under defined 808 nm LED irradiation conditions, supporting their continued development as nanotheranostic tools that integrate affibody-mediated specificity with plasmonic heating.