Hakima Cherif

Hakima Cherif


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 December 2015 in International Journal of System Assurance Engineering and Management
Verified
Journal Article
Closed access
PDF file
BBBesma Bessam
Besma Bessam
AMArezki Menacer
Arezki Menacer
MBMohamed Boumehraz
Mohamed Boumehraz
HCHakima Cherif
Hakima Cherif

15 September 2022 in Energies
Verified
Journal Article
Open access
PDF file
Seif Eddine ChehaidiaSeif Eddine Chehaidia
Seif Eddine Chehaidia
HCHakima Cherif
Hakima Cherif
MAMusfer Alraddadi
Musfer Alraddadi
Mohamed MosaadMohamed Mosaad
Mohamed Mosaad
ABAbdelaziz Mahmoud Bouchelaghem
Abdelaziz Mahmoud Bouchelaghem
Knowledge of the distinctive frequencies and amplitudes of broken rotor bar (BRB) faults in the induction motor (IM) is essential for most fault diagnosis methods. Fast Fourier transform (FFT) is widely applied to diagnose the faults within BRBs. However, this method does not provide satisfactory results if it is applied directly to the stator current signal at low slip because a high-resolution spectrum is required to separate the different components of the frequency. To address this problem, this paper proposes an efficient method based on a Hilbert fast Fourier transform (HFFT) approach, which is used to extract the envelope from the stator current using the Hilbert transform (HT) at low slip. Then, the stator current envelope is analyzed using the fast Fourier transform (FFT) to obtain the amplitude and frequency of the particular harmonic. These data were recently collected and selected as BRB fault features and were employed as adaptive neuro-fuzzy inference system (ANFIS) inputs for BRB fault autodiagnosis and classification. To identify the BRB defect by determining the number of broken bars in the rotor, two ANFIS models are proposed: ANFIS grid partitioning (ANFIS-GP) and ANFIS-subtractive clustering (ANFIS-SC). To validate the effectiveness of the proposed method, three different motors were used during experiments under various loads; the first was with one broken bar, the second was with two adjacent broken bars, and the third was a healthy motor. The obtained results confirmed the effectiveness and the robustness of the proposed method, which is based on the combination of HFFT-ANFIS-SC to diagnose the BRB faults and quantify the number of broken bars under different load conditions (under low and high slip) precisely with minimal errors (this method had an MSE of 10-14 and 10-7 for the RMSE) compared to the method based on the combination of HFFT-ANFIS-GP.

30 September 2020 in Periodicals of Engineering and Natural Sciences (PEN)
Verified
Journal Article
Open access
PDF file
HCHakima Cherif
Hakima Cherif
ABAbdelhamid Benakcha
Abdelhamid Benakcha
AKAbderrahmane Khechekhouche
Abderrahmane Khechekhouche
AMArezki Menacer
Arezki Menacer
SCSeif Eddine Chehaidia
Seif Eddine Chehaidia
HPHitesh Panchal
Hitesh Panchal
This paper presents a comparative study between two techniques of signal processing to diagnose both faults the inter-turn short circuit (ITSC) in stator windings and the unbalanced voltage supply (UVS) in induction motors. The first is considered a classical technique called Motor Current Signature Analysis (MCSA) which is based on the processing of the stator current by the Fast Fourier Transform (FFT). The second is anadvanced technique based on a Discrete Wavelet Energy Ratio (DWER) of three stator currents. The aim objective of this paper is to compare the ability and effectiveness of both techniques to detect the ITSC fault and the UVS in induction motors, and distinguishing between them. An experimental implementation tests the two diagnosis techniques.The results obtained show that the MCAS technique by the FFT analysis has a difficult to discriminate between the current harmonics due to the provide voltage unbalance and those originated by ITSC faults. Unlike the DWERtechnique, which has high sensitivity and exceptional ability to detect and distinguish between the two faults that lead to the reliability of the diagnosis system. To demonstrate that the DWER is an accurate and robust diagnosis approach are used the neural network (NN) as a tool to classify the faults (ITSC and USV) where using DWER indicators as NN input. The results obtained of combination between the DWER and NN are effective and proved its ability to detect both faults under different load conditions and distinguish between them accurately with low error (10-5).