Xinliang Li

Prof. Xinliang Li


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2023 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
SGShengzu Guo
Shengzu Guo
XZXu Zhang
Xu Zhang
QLQili Liu
Qili Liu
XLXinliang Li
Xinliang Li
The periodic flame flashback phenomenon in an ethylene-fueled cavity-based scramjet combustor was numerically investigated by a three-dimensional unsteady Reynolds-averaged Navier–Stokes solver with two-step kinetics. The air inflow stagnation temperature is 1225 K, and its Mach number is 2.6. Spectral analyses revealed the combustion oscillations with flame flashbacks maintained in the separated scramjet mode with the establishment/vanishment of flow separation near the fuel injector, differing from previous studies of flame flashbacks connected to the ramjet/scramjet mode transitions. A mechanism with four evolution stages was proposed to elucidate the flow-flame interaction. In stage I, a rapid flame flashback upstream and shock-train extension were caused by the high-temperature induced auto-ignition tendency of well-mixed unburned gas in the near-sidewall low-speed region. In stage II, the combustion-induced back pressure and shock train gradually achieved an aerodynamic balance. The combustion flow barely changed in stage III. Meanwhile, a simplified model suggested that the gradual temperature rises occurring upstream of the cavity and away from the sidewall were caused by spanwise heat conduction. The higher temperatures would cause upstream flame propagation with enhanced heat release due to auto-ignition. However, the enhanced heat release occurred mostly in the subsonic flow, resulting in pressure decreases according to one-dimensional flow equations. A smaller near-sidewall separation was produced by the lower back-pressures, which prompted the rapid flame recession downstream in stage IV. Moreover, a simplified flame-spreading model was proposed to illuminate the flame propagation nature. The comparison of flame speeds with theoretical estimations indicated that the current flame was in the regime of turbulent flame propagation, rather than the C–J detonation or deflagration speculated in previous studies.

1 September 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
CHChengming He
Chengming He
WLWeihang Luo
Weihang Luo
PZPeng Zhang
Peng Zhang
Zhi-xia HeZhi-xia He
Zhi-xia He
XLXinliang Li
Xinliang Li
The present paper experimentally verified and computationally explained an improved design concept of the spray combustion of a gas–liquid pintle injector with variable swirl intensities. By pintle injector, we mean a promising injector for the throttleable engines with variable thrust capacities, which features the moveable pintle continuously controlling the mass flow rates of fuel and oxidizer where the radial and axial flows encounter to form a spray cone and spray atomization. First, the cold flow test was conducted to study the swirl effects on the spray angle, followed by the combustion test to study the total pressure and the specific impulse under different swirl intensities. The results show that the swirl enhances the combustion performance by increasing the total pressure and specific impulse. Second, the swirl-assisted spray was numerically simulated based on a validated volume-of-fluid method to explain the experimental findings. The diameter distribution and spatial distribution of dispersed droplets were analyzed by the Sauter mean diameter (SMD) and the Voronoi tessellation, respectively. The results show that the swirl significantly promotes the breakup of liquid jet or film, producing smaller SMDs and a more uniform spatial distribution of dispersed droplets. The consolidated correlation between the non-reacting spray characteristics and the combustion performance suggests that the proposed methodology can be used to fast prescreen pintle injector designs.

1 August 2021 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
GZGongXi Zhou
GongXi Zhou
XZXu Zhang
Xu Zhang
JLJinping Li
Jinping Li
XZXiaoyuan Zhang
Xiaoyuan Zhang
SZShizhong Zhang
Shizhong Zhang
XYXiLong Yu
XiLong Yu

1 September 2022 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
QZQifan Zhang
Qifan Zhang
HCHao Chen
Hao Chen
ZWZhenjie Wu
Zhenjie Wu
ZGZhanbiao Gao
Zhanbiao Gao
WLWeihang Luo
Weihang Luo
XLXinliang Li
Xinliang Li
Understanding the hypersonic inlet starting characteristics is the prerequisite for avoiding the abnormal unstart state. To make the work close to the actual situation, an experimental study was performed on a scramjet model at a simulated freestream Mach number of 6.0 with pressure and thrust measurements. The inlet working status is determined by the heat release of the injected ethylene with reciprocating variations. The results show that the critical equivalence ratio of the restart state is lower than that of the unstart state, which means that the combustion weakens the inlet restart capability and raises the unstart/restart hysteresis phenomena. Specifically, two novel unstart/restart hysteresis phenomena are found: one may come from the dual-solution characteristics of the shock–combustion interaction and the other may come from the historical effect of reverse flow. Compared to the former type, the latter type requires greater downstream heat release and generates a larger hysteresis loop. In addition, the engine thrust characteristics of the whole unstart and restart processes are analyzed. The thrust increment in the shock–combustion interaction type exhibits nearly linearly. However, the thrust increment meets abrupt changes and strong oscillations in the reverse flow type, accompanied by the reverse flow's formation and disappearance, making the engine more difficult to restart.

18 February 2014 in Science China Physics, Mechanics & Astronomy
Verified
Journal Article
Open access
PDF file
HLHongBo Lu
HongBo Lu
XLXinliang Li
Xinliang Li
XCXinYu Chang
XinYu Chang
Under hypersonic flight conditions, the sharp cowl-lip leading edges have to be blunted because of the severe aerodynamic heating. This paper proposes four cowl-lip blunting methods and studies the corresponding flow characteristics and performances of the generic hypersonic inlets by numerical simulation under the design conditions of a flight Mach number of 6 and an altitude of 26 km. The results show that the local shock interference patterns in the vicinity of the blunted cowl-lips have a substantial influence on the flow characteristics of the hypersonic inlets even though the blunting radius is very small, which contribute to a pronounced degradation of the inlet performance. The Equal Length blunting Manner (ELM) is the most optimal in that a nearly even reflection of the ramp shock produces an approximately straight and weak cowl reflection shock. The minimal total pressure loss, the lowest cowl drag, maximum mass-capture and the minimal aeroheating are achieved for the hypersonic inlet. For the other blunting manners, the ramp shock cannot reflect evenly and produces more curved cowl reflection shock. The Type V shock interference pattern occurs for the Cross Section Cutting blunting Manner (CSCM) and the strongest cowl reflection shock gives rise to the largest flow loss and drag. The cowl-lip blunted by the other two blunting manners is subjected to the shock interference pattern that transits with an increase in the blunting radius. Accordingly, the peak heat flux does not fall monotonously with the blunting radius increasing. Moreover, the cowl-lip surface suffers from severe aerothermal load when the shear layer or the supersonic jet impinges on the wall.

1 June 2022 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
LHLi-Hao He
Li-Hao He
HCHao Chen
Hao Chen
XLXinliang Li
Xinliang Li
QZQi-Fan Zhang
Qi-Fan Zhang
WWWan-Nan Wu
Wan-Nan Wu
Shock-train transitions in simplified curved isolators are carefully studied by simulation. The results show the shock-train behavior is subject to the complex pressure field created by the duct deflection, eventually presenting five modes during a backpressure-varying process. Of them, the most special one is the abrupt shock-train leap. It appears as the leading shocks interact with an adverse pressure gradient and follows a different path after a reversal of the direction the backpressure takes, which causes a shock-train hysteresis. If the curvature increases, the leap phenomenon, together with the related hysteresis, grows in number and intensity. Analysis indicates the background pressure gradients stem from the inherent left-running expansion waves and right-running compression waves. They control alternately the near-wall flow state, provoking the cyclic changes in the pressure gradient sign. Unlike the former, the latter can enhance separation through a positive feedback mechanism, rendering the shock train highly sensitive to backpressure. This is why the leap occurs. Comparing with the previously reported shock-induced leap indicates that there is a marked similarity in their behaviors, suggesting the irrelevance of the occurrence of a leap to the category of incident waves. Nevertheless, a delay in the onset usually follows a compression-wave-typed leap, which reflects that there is a triggering threshold for an incident wave. Given the fact that no local separation is provoked by the compression waves, it is speculated that the threshold should lie below the criterion for causing a separation, as opposed to the impression from the previous research.