Silica from geothermal power plant waste was studied as a filler for rubber compound. Utilization of geothermal silica will be beneficial both to the rubber and power industries. Rubber industries got benefit from its low cost and the potential as reinforcing filler in rubber compounds, and power industries benefited by resolving waste problems in the geothermal facilities. The effect of geothermal silica addition on the rubbers compound and vulcanizate were investigated. The rheometer, FTIR, UTM, and SEM were used to study the vulcanization process, development of crosslink and mechanical properties of the rubber. The results showed that the compound using geothermal silica had faster curing time, better swelling properties, but lower mechanical properties compared to commercial silica.
31 August 2023 in Indonesian Journal of Halal Research
The halal certification of products holds significant importance for Muslim consumers, necessitating the development of reliable techniques for identifying leather products made from raw materials. This study employed rapid and accurate analytical methods to distinguish between cowhide, pigskin, and artificial leather. A combination of scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC) was used to assess the variations in collagen fiber structures and thermal stability among the leather samples. The findings revealed that morphological surface analysis, including grain patterns and pores, facilitated swift differentiation between different leather types. Pigskins exhibit three-hole patterns on their morphological surface compared to cowhide, with random pores and tighter grain patterns, whereas artificial leather lacks natural grain patterns and pores altogether. While FTIR spectra exhibited similarities between cowhide and pigskin leathers, variations in vibration intensity enabled effective discrimination. Artificial leather, particularly PVC-based materials, displayed distinct spectra, allowing FTIR spectroscopy to effectively discern between halal and non-halal leather. Cowhide possesses strong and sharp vibration at wavenumber 1736, 1277, and 817 cm-1 compared to pigskin, which has stronger vibration at 1534 cm-1. Meanwhile, PVC-based artificial leather exhibited stretching at 1723 and 744 cm-1 wavenumbers. DSC analysis proved valuable in differentiating between genuine and artificial leather based on unique peaks and thermal behavior. These three techniques provide reliable means to determine the raw material origins of leather products.
1 January 2020 in IOP Conference Series: Materials Science and Engineering
The amount of plastic waste has always increased over the years and caused many problems in the environment because of its poor degradation rate characteristics. Recently, the interest in biodegradable polymer to substitute these synthetic plastic materials has been increased. Biocomposite materials have better biodegradability rate and can be utilized for several applications, such as packaging, agriculture, biomedical and healthcare. Chitosan as natural polymer that has good biodegradability can be combined with low density polyethylene (LDPE) to improve its mechanical properties. The LDPE-chitosan biocomposites were made by mixing chitosan and LDPE with maleic anhydride as compatibilizer and perbutyl Z as an initiator. In this study, the decomposition kinetic and thermal behavior of low density polyethylene (LDPE)-chitosan biocomposites were investigated by thermogravimetric analysis (TGA). The residual weight of biocomposites after decomposition process was analyzed. The samples were heated in the range of temperature from 25 °C to 500 °C and at different heating rates of 5, 10, 15, 20 °C/min, respectively. The result shows that activation energy decreased along with the increasing of chitosan concentration. This result indicates that the LDPE-chitosan biocomposite is a promising candidate for substitution of synthetic plastic.
10 July 2023 in Communications in Science and Technology
The present study investigates the effects of nanoparticle geothermal silica (NGS) on the mechanical properties and vulcanization characteristics of rubber compounds with various filler loadings. The rubber compounds were filled with 0, 20, 30, and 40 phr of silica. The properties of NGS were analyzed using transmission electron microscopy, particle size analyzer, and BET surface area analysis to examine its morphology, size distribution, and surface area. The mechanical properties and vulcanization characteristics of the rubber compounds reinforced with NGS were evaluated using a universal testing machine and moving die rheometer. The results showed that NGS possessed the primary particle sizes below 20 nm and a surface area of 168.35 m2/g. The interaction between silica and rubber determined the modulus of the rubber composites and the vulcanization characteristics. The tensile strength of the rubber compounds, meanwhile, showed a significant increase more than threefold as the filler loading increased from 0 phr to 30 phr, followed by a slight decline at 40 phr loading. The addition of 20 phr of silica led to a prolonged scorch time compared to the filler-free compound due to the adsorption of activators and accelerators. However, the scorch time decreased after reaching 30 phr of silica loading, which could be attributed to the higher amount of bound rubber covering a portion of the silica surface, thereby reducing its ability to adsorb the activator. The presence of silica with good thermal conductivity enabled a better heat transfer during the vulcanization process, resulting in shorter curing times for higher loading. Rubber compounds with an NGS loading of 30 phr demonstrated a favorable balance between filler-rubber interactions, vulcanization characteristics, and mechanical properties in the rubber compounds.
Synthetic leather is generally made using polyvinyl chloride or polyurethane resins by coating method. The balance between quality and production costs of the final product is influenced by the selection of the right material composition. Polyvinyl chloride resins are available in a variety of k-values, while fillers are often added to modify mechanical characteristics and lower the costs. The aim of this study was to examine the effect of the k-value of polyvinyl chloride blend and the amount of filler on the quality of synthetic leather. Plastisol is prepared by mixing resin, primary plasticizer, secondary plasticizer, and stabilizer according to the formulation. PVC resin blend with different k-values and certain amount of filler (10, 20, 30 and 40 phr) were used. The quality of the samples was tested using adhesion strength, tensile strength, and elongation at break testing according to ASTM D751-06. The results showed that resins blend with different k-values could be used to obtain the desired quality. The value of the adhesion strength, tensile strength and elongation at break will approach the characteristics of the larger part of the resin. The homogeneity of plastisol because of resin blend also needs attention, especially if the k-value difference between two resin is too large. Meanwhile, the use of calcium carbonate as filler in general will reduce the test results obtained.
6 October 2026 in BIDIK: Jurnal Pengabdian kepada Masyarakat
Increased activity in the Segajih Tourism Village, Kulon Progo, has led to a surge in the volume of waste managed by the "Uwuh Mulyo" Waste Bank. This community service program aimed to improve waste-processing skills aligned with a circular economy for waste bank activists. The intensive training used an andragogical approach, comprising theory, practice, discussion, and evaluation. The materials focused on waste sorting methods, waste management, and technology to turn waste into plastic yarn. The results showed a significant increase in participants' cognitive capacity, with the mean pre-test score rising from 64.29 to 85.24 in the post-test. Post-activity evaluations indicated excellent responses, with an instructor performance score of 89.73 (100 scale) and event satisfaction at 4.51 (5 scale). This training successfully minimized skill barriers and established social capital for sustainable waste management.