Daejin Jang

Dr. Daejin Jang

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2024 in Sensors
Verified
Journal Article
Open access
PDF file
SYSumin Yang
Sumin Yang
BKBummo Koo
Bummo Koo
SLSeung Hee Lee
Seung Hee Lee
DJDaejin Jang
Daejin Jang
HSHyunjun Shin
Hyunjun Shin
YKYoungho Kim
Youngho Kim
Gait event detection is essential for controlling an orthosis and assessing the patient’s gait. In this study, patients wearing an electromechanical (EM) knee–ankle–foot orthosis (KAFO) with a single IMU embedded in the thigh were subjected to gait event detection. The algorithm detected four essential gait events (initial contact (IC), toe off (TO), opposite initial contact (OIC), and opposite toe off (OTO)) and determined important temporal gait parameters such as stance/swing time, symmetry, and single/double limb support. These gait events were evaluated through gait experiments using four force plates on healthy adults and a hemiplegic patient who wore a one-way clutch KAFO and a pneumatic cylinder KAFO. Results showed that the smallest error in gait event detection was found at IC, and the largest error rate was observed at opposite toe off (OTO) with an error rate of −2.8 ± 1.5% in the patient group. Errors in OTO detection resulted in the largest error in determining the single limb support of the patient with an error of 5.0 ± 1.5%. The present study would be beneficial for the real-time continuous monitoring of gait events and temporal gait parameters for persons with an EM KAFO.

10 January 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DJDaejin Jang
Daejin Jang
YKYong-Cheol Kim
Yong-Cheol Kim
EHEung-Pyo Hong
Eung-Pyo Hong
GKGyu Seok Kim
Gyu Seok Kim
This paper presents the design process and driving performance test results of a power-assist module to which a cycloidal reducer is applied in order to convert a manual wheelchair into an electric wheelchair. The types of electrification modules currently used to electrify manual wheelchairs include front-mounted, rear-mounted, and powered wheels. These assist devices are either difficult to carry and transport independently or require excellent hand dexterity to operate. To overcome this problem, a cycloidal reducer with no pin roller, and a novel cycloidal curve were designed to develop a small and easy-to-handle power-assist module that was tested by installing this reducer to a manual wheelchair. As a result of the test, the maximum speed of the wheelchair was 6 km/h, the maximum slope that this wheelchair can climb is 20%, and 0.358 Ah was consumed while the wheelchair moved 360 m in the current consumption test. This showed that it is possible to develop a small-sized power-assist module. In addition, the user can easily electrify the manual wheelchair by adding a small weight without replacing the manual wheel. The power-assist module consists of a DC servo motor, cycloidal reducer, battery, and joystick.

1 October 2018 in Journal of the Korean Society for Precision Engineering
Verified
Journal Article
Closed access
DJDaejin Jang
Daejin Jang
YKYong Cheol Kim
Yong Cheol Kim
SKShin Ki Kim
Shin Ki Kim
JRJe Cheong Ryu
Je Cheong Ryu
This study shows the 4 - Bar linkage design process and static/dynamic stability analysis of a foldable electric wheelchair that can be loaded into a vehicle for long-distance trips. Conventional foldable electric wheelchairs have been developed for indoor use because the safety of the disabled is not secure enough for outdoor use. However, the disabled have generally used foldable electric wheelchairs for outdoor use, potentially putting themselves in a dangerous situation. The body of a foldable electric wheelchair consists of a double 4 - Bar linkage system that shares one link. The architecture of the wheelchair’s four-bar linkage frame was synthesized using four finitely separated design positions. This simple method can design a planar four-bar mechanism through the use of four finitely separated poses (orientation and position). The power driving module includes a battery and controller, and can be separated to load into a car easily. An analysis of the tip-over measurement was performed using ADAMS and LifeMOD during a maneuver on the ground. by force-moment stability metric. Several elements, including the center of gravity position, rotational radius, and acceleration, were evaluated how to affect stability metric.