On February 6, 2023 (local time), two earthquakes (Mw7.8 and Mw7.7) struck central and southern Turkey, causing extensive damage to several cities and claiming a toll of 40,000 lives. In this study, we propose a method for seismic building damage assessment and analysis by combining SAR amplitude and phase coherence change detection. We determined building damage in five severely impacted urban areas and calculated the damage ratio by measuring the urban area and the damaged area. The largest damage ratio of 18.93% is observed in Nurdagi, and the smallest ratio of 7.59% is found in Islahiye. We verified the results by comparing them with high-resolution optical images and AI recognition results from the Microsoft team. We also used pixel offset tracking (POT) technology and D-InSAR technology to obtain surface deformation using Sentinel-1A images and analyzed the relationship between surface deformation and post-earthquake urban building damage. The results show that Nurdagi has the largest urban average surface deformation of 0.48 m and Antakya has the smallest deformation of 0.09 m. We found that buildings in the areas with steeper slopes or closer to earthquake faults have higher risk of collapse. We also discussed the influence of SAR image parameters on building change recognition. Image resolution and observation geometry have a great influence on the change detection results, and the resolution can be improved by various means to raise the recognition accuracy. Our research findings can guide earthquake disaster assessment and analysis and identify influential factors of earthquake damage.

In February 2023, Mw 7.8 and Mw 7.7 earthquakes struck southeastern Turkey. Generating a coseismic 3D deformation field that can directly reflect the characteristics of surface deformation is important for revealing the movement mode of a seismogenic fault and analyzing the focal mechanism. Optical image sub-pixel correlation (SPC) only captures deformation in the horizontal direction, and SAR image pixel offset tracking (POT) obtains range deformation that is not sensitive to north–south deformation signals. Thus, neither of them can capture the complete 3D deformation alone. Combining them may be able to allow the monitoring of 3D deformation. In this study, we used Sentinel-2 optical images to obtain the horizontal deformation (east–west and north–south) and Sentinel-1 and ALOS-2 data to extract the range and azimuth offsets. The least-squares method was used to fuse the optical and SAR offsets to obtain the 3D deformation field of the 2023 Turkey earthquake sequence, which indicates that the two events were both left-lateral strike-slip earthquakes. The surface deformation caused by the two large earthquakes is mainly in the east–west direction. In the vertical direction, the two earthquakes caused a small-magnitude uplift and subsidence. The findings in this paper can be used as a reference for the study of coseismic 3D deformation.

The joint action of human activities and environmental changes contributes to the frequent occurrence of landslide, causing major hazards. Using Interferometric Synthetic Aperture Radar (InSAR) technique enables the detailed detection of surface deformation, facilitating early landslide detection. The growing availability of SAR data and the development of artificial intelligence have spurred the integration of deep learning methods with InSAR for intelligent geological identification. However, existing studies using deep learning methods to detect landslides in InSAR deformation often rely on single InSAR data, which leads to the presence of other types of geological hazards in the identification results and limits the accuracy of landslide identification. Landslides are affected by many factors, especially topographic features. To enhance the accuracy of landslide identification, this study improves the existing geological hazard detection model and proposes a multi-source data fusion network termed MSFD-Net. MSFD-Net employs a pseudo-Siamese network without weight sharing, enabling the extraction of texture features from the wrapped deformation data and topographic features from topographic data, which are then fused in higher-level feature layers. We conducted comparative experiments on different networks and ablation experiments, and the results show that the proposed method achieved the best performance. We applied our method to the middle and upper reaches of the Yellow River in eastern Qinghai Province, China, and obtained deformation rates using Sentinel-1 SAR data from 2018 to 2020 in the region, ultimately identifying 254 landslides. Quantitative evaluations reveal that most detected landslides in the study area occurred at an elevation of 2500–3700 m with slope angles of 10–30°. The proposed landslide detection algorithm holds significant promise for quickly and accurately detecting wide-area landslides, facilitating timely preventive and control measures.

The azimuth displacement derived by pixel offset tracking (POT) or multiple aperture InSAR (MAI) measurements is usually used to characterize the north-south coseismic deformation caused by large earthquakes ($M$ > 6.5), but its application in the source parameter inversion of moderate-magnitude earthquakes (~$M$ 6.0) is rare due to the insensitive observation accuracy. Conventional line-of-sight (LOS) displacements derived by the Interferometric Synthetic Aperture Radar (InSAR) have limited ability to constrain the source parameters of the earthquake with near north-south striking. On 21 May 2021, an $M_w$ 6.1 near north-south striking earthquake occurred in Yangbi County, Yunnan Province, China. In this study, we derive both the coseismic LOS displacement and the burst overlap interferometry (BOI) displacement from the Sentinel-1 data to constrain the source model of this event. We construct a single-segment fault geometry and estimate the coseismic slip distribution by inverting the derived LOS and BOI-derived azimuth displacements. Inversion results show that adding the BOI-derived azimuth displacements to source modeling can improve the resolution of the slip model by ~15% compared with using the LOS displacements only. The coseismic slip is mainly distributed 2 to 11 km deep, with a maximum slip of approximately 1.1 m. Coulomb stress calculation shows a maximum Coulomb stress increment of ~0.05 Mpa at the north-central sub-region of the Red River Fault. In addition, there is a small Coulomb stress increase at the Southern end of the Weixi-Weishan fault. The potential seismic risks on the Weixi-Weishan and Northwest section of the Red River faults should be continuously monitored.

The optical image sub-pixel correlation (SPC) technique is an important method for monitoring large-scale surface deformation. RapidEye images, distinguished by their short revisit period and high spatial resolution, are crucial data sources for monitoring surface deformation. However, few studies have comprehensively analyzed the error sources and correction methods of the deformation field obtained from RapidEye images. We used RapidEye images without surface deformation to analyze potential errors in the offset fields. We found that the errors in RapidEye offset fields primarily consist of decorrelation noise, orbit error, and attitude jitter distortions. To mitigate decorrelation noise, the careful selection of offset pairs coupled with spatial filtering is essential. Orbit error can be effectively mitigated by the polynomial fitting method. To address attitude jitter distortions, we introduced a linear fitting approach that incorporated the coherence of attitude jitter. To demonstrate the performance of the proposed methods, we utilized RapidEye images to extract the coseismic displacement field of the 2019 Ridgecrest earthquake sequence. The two-dimensional (2D) offset field contained deformation signals extracted from two earthquakes, with a maximum offset of 2.8 m in the E-W direction and 2.4 m in the N-S direction. A comparison with GNSS observations indicates that, after error correction, the mean relative precision of the offset field improved by 92% in the E-W direction and by 89% in the N-S direction. This robust enhancement underscores the effectiveness of the proposed error correction methods for RapidEye data. This study sheds light on large-scale surface deformation monitoring using RapidEye images.