Thirty-six volatile compounds, composed of 18 esters, 10 terpenes, and 8 others, were detected by headspace-solid phase microextraction (HS-SPME) equipped with gas chromatography-mass spectrometry (GC-MS) in mango and vodka cocktail. Moreover, these compounds were detected by olfactometry using aroma intensities. Comparing these compounds revealed that the aroma intensities (AIs) of limonene, 3-carene, myrcene, β-caryophyllene, and citronellyl propanoate were higher than others (AIs ≥ 4). In this context, limonene was selected as the reference compound on the basis of the strongest component model. The aim of this study was to determine the perceptual interaction between limonene and 3-carene, myrcene, β-caryophyllene, citronellyl propanoate, respectively, in a binary mixture. In addition, feller’s addition model revealed that limonene presented an addition effect when combined with 3-carene, myrcene, β-caryophyllene, and citronellyl propanoate. It could be stated that these compounds played an important role in the aroma of mango and vodka cocktail. The results demonstrated that molecular structure and the ratio between compounds affected the synergistic effect, and compounds with similar structure and aroma were more prone to undergo addition and synergy.
Guaiacol (2-methoxyphenol), an important fine chemical intermediate, is conventionally synthesized by liquid-phase processes with expensive, corrosive and toxic methylating agents such as dimethyl sulphate and dimethyl iodide. Recently, vapour-phase alkylation of catechol (1, 2-dihydroxybenzene) with methanol for the synthesis of guaiacol in the presence of heterogeneous catalysts has received more attention, as the route is economical and environmentally friendly. However, most of the investigated catalysts exhibited unsatisfactory catalytic performance for industrial applications. In this study, five metal phosphates M-P-O (M = La, Ce, Mg, Al, Zn) catalysts were synthesized and tested in the selective O-methylation of catechol with methanol. Among these catalysts, cerium phosphate (CP) showed the highest catalytic activity and guaiacol yield. Lanthanum phosphate (LP) was the second most active, which was still obviously better than magnesium phosphate (MP) and aluminium phosphate (ALP). Zinc phosphate (ZP) was not active in the reaction. Relevant samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), N2 adsorption-desorption, temperature programmed desorption of NH3 or CO2 (NH3-TPD, CO2-TPD). The suitable acid-base properties contribute to the superior catalytic performance of CP. Long-term stability and regeneration tests were also studied.
Rational surface engineering of noble metal-doped photocatalysts is essential for the efficient conversion of solar energy into chemical energy, but it is still challenging to perform. Herein, we reported an effective strategy for structuring alloyed CuPd (CP) nanoclusters on the ordered mesoporous TiO2 (CPT) by a pore confinement effect. The resultant CPT exhibited an extraordinary photocatalytic activity during Stille reaction under visible light. The X-ray photoelectron spectroscopy spectra, the field emission scanning electron microscope (FESEM) images, and the aberration-corrected high-angle annular dark scanning transmission electron microscopy (HAADF-STEM) images demonstrated that CP nanoclusters were anchored in the mesoporous pore wall of TiO2, and the atomic ratio as well as densities of CP could be precisely modulated via the coordination configuration. As the atomic ratio of CP to TiO2 increased to a certain extent, their photocatalytic activity during Stille reaction increased. A mechanistic investigation suggested that the CP alloy could absorb visible light and its conduction electrons gained energy, which were available at the surface Pd sites. This allowed the Pd sites to become electron-rich and to accelerate the rate-determining step of the Stille reaction. As a result, the efficiency of the photocatalytic Stille coupling reaction was extraordinary enhanced.
According to the requirements for sustainable development, reclaiming fine chemicals from wastewater under mild conditions is an extremely significant line of research. A low-cost and high-efficiency polydentate chelate- and polymeric Co(II)-based complex (Co-L)-loaded C3N4 photocatalyst (Co-L/C3N4) was constructed and used to convert aromatic mandelic acids in wastewater at room temperature. The BET specific surface area increased from 28 m2 g−1 to 68 m2 g−1, indicating its excellent absorptive character. The light absorption range of Co-L/C3N4 reached 650 nm, while the band energy reduced to 2.30 eV, which caused a significant enhancement in photocatalytic activity. The conversion of substituted mandelic acids was more than 90% due to the photoactivity of Co-L/C3N4. Time-resolved PL spectra indicated the remarkable separation of the photogenerated electron–hole pairs in Co-L/C3N4. Furthermore, the UV-vis and in situ FTIR spectra indicated the formation of aldehyde groups in the selective oxidation process, which provided support for the plausible catalytic mechanism.
Aimed at greenhouse gas CO2 high value-added utilization, a N,N′-(propane-1,3-diyl)dipicolinamide (PPPA) supported Al(iii) metal–organic polydentate chelate complex (Al-PPPA) was designed and used to efficiently catalyze CO2 to cyclic carbonates.
Microreactors are essential for microchemical reactions owing to their high mass transfer efficiency, precise control of reaction time, easy amplification, and good safety performance. These characteristics provide several advantages, including shortened reaction times and enhanced chemical reaction conversion rates, rendering microreactors particularly significant in chemical production. In this study, a finite-rate model was developed for the esterification of monobutyl chlorophosphate (MCP) and n-butanol in a microchannel reactor. This study investigates the impact of the microchannel’s length-to-diameter ratio, the mass ratio of n-butanol to MCP at the inlet, and the inlet flow ratio on the entire reaction system through numerical simulations. The findings indicate that increasing the length-to-diameter ratio and reducing the inlet flow rate effectively prolongs the residence time of materials in the microreactor, thereby enhancing the conversion rate of the reactants. Optimal results are achieved with a moderate n-butanol/MCP mass ratio, which facilitates MCP transformation. Moreover, this study employs response surface analysis to investigate the influence of independent factors, such as the microchannel’s length-to-diameter ratio, component ratio, and inlet velocity ratio, on MCP conversion rates. A prediction formula with conversion rate as the dependent variable and microchannel length-to-diameter ratio, component ratio, and inlet velocity ratio as independent variables was established.