Microreactors are essential for microchemical reactions owing to their high mass transfer efficiency, precise control of reaction time, easy amplification, and good safety performance. These characteristics provide several advantages, including shortened reaction times and enhanced chemical reaction conversion rates, rendering microreactors particularly significant in chemical production. In this study, a finite-rate model was developed for the esterification of monobutyl chlorophosphate (MCP) and n-butanol in a microchannel reactor. This study investigates the impact of the microchannel’s length-to-diameter ratio, the mass ratio of n-butanol to MCP at the inlet, and the inlet flow ratio on the entire reaction system through numerical simulations. The findings indicate that increasing the length-to-diameter ratio and reducing the inlet flow rate effectively prolongs the residence time of materials in the microreactor, thereby enhancing the conversion rate of the reactants. Optimal results are achieved with a moderate n-butanol/MCP mass ratio, which facilitates MCP transformation. Moreover, this study employs response surface analysis to investigate the influence of independent factors, such as the microchannel’s length-to-diameter ratio, component ratio, and inlet velocity ratio, on MCP conversion rates. A prediction formula with conversion rate as the dependent variable and microchannel length-to-diameter ratio, component ratio, and inlet velocity ratio as independent variables was established.
The production of menthol via thymol hydrogenation is an industrial technology but is challenging due to the unsatisfied selectivity to menthol. Herein, Ni/Ce catalysts were prepared and used in thymol hydrogenation. A high selectivity of menthol was achieved over Ni4/Ce1 catalysts under the optimized reaction condition. Ce incorporation can improve both the activity of Ni catalyst and the selectivity to menthol. To reveal the functions of Ce, catalyst characterizations were conducted. The catalytic activity improvement may be related to the remarkable increase in the surface area of the catalyst and the lower crystalline sizes of Ni that take place when a tiny amount of Ce is incorporated into Ni. Higher selectivity to menthol may be related to the modification of the acidity of an Ni catalyst. In addition, the stability of the Ni4/Ce1 catalysts was also evaluated, and after five recycles, the Ni4/Ce1 catalysts exhibited outstanding catalytic activity and stability.
Three types of Zr-based metal–organic frameworks (Zr-MOFs) were employed as supports to prepare monometallic Rh catalysts by the impregnation method. The effects of the structural properties of Zr-MOFs on their supported monometallic Rh catalysts for syngas conversion were investigated. The results showed that, compared to catalysts with Rh@MOF-808 and Rh@UiO-66, Rh@UiO-67 had higher CO conversion and C2+ oxygenate selectivity. The state of the Rh site is affected by the different structure of the Zr-MOFs, which is responsible for the difference in catalytic performance. The relatively higher Rh dispersion on the UiO-67 support boosted its CO adsorption ability, and Rh@UiO-67 having the best C2+ oxygenate selectivity was mainly attributed to it having the highest Rh+/Rh0 ratio.
This study investigates the continuous-flow hydrolysis reaction of propylene oxide (PO) in a spiral microchannel reactor, integrating experiments, computational fluid dynamics (CFD) simulations, and response surface methodology (RSM). To the best of our knowledge, experimentally determined apparent Arrhenius parameters for PO hydrolysis under microscale continuous-flow conditions remain rarely reported, and afterwards they were incorporated into CFD-based numerical simulations. This combined experimental–numerical framework provides a robust methodology for quantifying and optimizing liquid-phase kinetics in microscale flow environments. Subsequently, CFD simulations were employed to examine key process parameters, including reaction system temperature, inlet flow rate, and reactor length. Finally, RSM was utilized to identify the optimal process conditions (reaction system temperature of 298.15 K, inlet flow rate of 6 × 10−3 m·s−1, and reactor length of 4 m), achieving a predicted PO conversion rate of 81.68%. The study provides a reference for designing and optimizing spiral microchannel reactors for PO hydrolysis.