Nuclear fusion between protons and boron-11 nuclei has undergone a revival of interest thanks to the rapid progress in pulsed laser technology. Potential applications of such reaction range from controlled nuclear fusion to radiobiology and cancer therapy. A laser-driven fusion approach consists in the interaction of high-power, high-intensity pulses with H- and B-rich targets. We report on an experiment exploiting proton-boron fusion in CN-BN targets to obtain high-energy alpha particle beams (up to 5 MeV) using a very compact approach and a tabletop laser system with a peak power of ~10 GW, which can operate at high-repetition rate (up to 1 kHz). The secondary resonance in the cross section of proton-boron fusion (~150 keV in the center-of-mass frame) is exploited using a laser-based approach. The generated alpha particles are characterized in terms of energy, flux, and angular distribution using solid-state nuclear-track detectors, demonstrating a flux of ~10⁵ particles per second at 10 Hz, and ~10⁶ per second at 1 kHz. Hydrodynamic and particle-in-cell numerical simulations support our experimental findings. Potential impact of our approach on future spread of ultra-compact, multi-MeV alpha particle sources driven by moderate intensity (10¹⁶-10¹⁷W/cm²) laser pulses is anticipated.

In this paper, we introduce a method to efficiently use a high-energy pulsed 1.7 ps HiLASE Perla laser system for two beam interference patterning. The newly developed method of large-beam interference patterning permits the production of micro and sub-micron sized features on a treated surface with increased processing throughputs by enlarging the interference area. The limits for beam enlarging are explained and calculated for the used laser source. The formation of a variety of surface micro and nanostructures and their combinations are reported on stainless steel, invar, and tungsten with the maximum fabrication speed of 206 cm²/min. The wettability of selected hierarchical structures combining interference patterns with 2.6 µm periodicity and the nanoscale surface structures on top were analyzed showing superhydrophobic behavior with contact angles of 164°, 156°, and 150° in the case of stainless steel, invar, and tungsten, respectively.

Superhydrophobic surfaces attract a lot of attention due to many potential applications including anti-icing, anti-corrosion, self-cleaning or drag-reduction surfaces. Despite a list of attractive applications of superhydrophobic surfaces and demonstrated capability of lasers to produce them, the speed of laser micro and nanostructuring is still low with respect to many industry standards. Up-to-now, most promising multi-beam solutions can improve processing speed a hundred to a thousand times. However, productive and efficient utilization of a new generation of kW-class ultrashort pulsed lasers for precise nanostructuring requires a much higher number of beams. In this work, we introduce a unique combination of high-energy pulsed ultrashort laser system delivering up to 20 mJ at 1030 nm in 1.7 ps and novel Diffractive Laser-Induced Texturing element (DLITe) capable of producing 201 × 201 sub-beams of 5 µm in diameter on a square area of 1 mm². Simultaneous nanostructuring with 40,401 sub-beams resulted in a matrix of microcraters covered by nanogratings and ripples with periodicity below 470 nm and 720 nm, respectively. The processed area demonstrated hydrophobic to superhydrophobic properties with a maximum contact angle of 153°.

A systematic experimental study was performed to determine laser irradiation conditions for the large-area fabrication of highly regular laser-induced periodic surface structures (HR-LIPSS) on a 220 nm thick Mo film deposited on fused silica. The LIPSS were fabricated by scanning a linearly polarized, spatially Gaussian laser beam at 1030 nm wavelength and 1.4 ps pulse duration over the sample surface at 1 kHz repetition rate. Scanning electron microscope images of the produced structures were analyzed using the criterion of the dispersion of the LIPSS orientation angle (DLOA). Favorable conditions, in terms of laser fluence and beam scanning overlaps, were identified for achieving DLOA values <10${}^{\circ }$. To gain insight into the material behavior under these irradiation conditions, a theoretical analysis of the film heating was performed, and surface plasmon polariton excitation is discussed. A possible effect of the film dewetting from the dielectric substrate is deliberated.

The generation, detection, and quantification of high-energy proton spectra that are produced from laser-target interaction methodologies is a field of increasingly growing popularity over the last 20 years. Generation methods such as target normal sheath acceleration or similar allow for collimated laminar ion beams to be produced in a compact environment through the use of short-burst terawatt lasers and are a growing field of investment. This project details the development and refinement of a python-based code to analyze time-of-flight ion spectroscopy data, with the intent to pinpoint the maximum proton energy within the incident beam to as reliable and accurate a value as possible within a feasible processing time. TOF data for 2.2 × 10¹⁶ W/cm² intensity laser shots incident on a 2 mm Cu target that were gathered from the PERLA 1 kHz laser at the HiLASE center were used as training and testing data with the implementation of basic machine learning techniques to train these methods to the data being used. These datasets were used to ensure more widely applicable functionality, and accurate calculation to within 1% accuracy of an assumed correct value was seen to be consistently achievable for these datasets. This wider functionality indicates a high level of accuracy for previously unseen TOF datasets, regardless of signal/noise levels or dataset size, allowing for free use of the code in the wider field.

Efficient heat management of Yb:YAG thin disk based on new highly thermally conductive crystalline coating is proved by thermal and lasing characteristics when it is used in a simple, multi-mode laser cavity under 940-nm pumping.