Surfactant-based viscoelastic (SBVE) fluids are innovative nonpolymeric non-newtonian fluid compositions that have recently gained much attention from the oil industry. SBVE can replace traditional polymeric fracturing fluid composition by mitigating problems arising during and after hydraulic fracturing operations are performed. In this study, SBVE fluid systems which are entangled with worm-like micellar solutions of cationic surfactant: cetrimonium bromide or CTAB and counterion inorganic sodium nitrate salt are synthesized. The salt reagent concentration is optimized by comparing the rheological characteristics of different concentration fluids at 25 °C. The study aims to mitigate the primary issue concerning these SBVE fluids: significant drop in viscosity at high temperature and high shear rate (HTHS) conditions. Hence, the authors synthesized a modified viscoelastic fluid system using ZnO nanoparticle (NPs) additives with a hypothesis of getting fluids with improved rheology. The rheology of optimum fluids of both categories: with (0.6 M NaNO3 concentration fluid) and without (0.8 M NaNO3 concentration fluid) ZnO NPs additives were compared for a range of shear rates from 1 to 500 Sec−1 at different temperatures from 25 °C to 75 °C to visualize modifications in viscosity values after the addition of NPs additives. The rheology in terms of viscosity was higher for the fluid with 1% dispersed ZnO NPs additives at all temperatures for the entire range of shear rate values. Additionally, rheological correlation function models were derived for the synthesized fluids using statistical analysis methods. Subsequently, Herschel–Bulkley models were developed for optimum fluids depending on rheological correlation models. In the last section of the study, the pressure-drop estimation method is described using given group equations for laminar flow in a pipe depending on Herschel–Bulkley-model parameters have been identified for optimum fluids are consistency, flow index and yield stress values.
The oil and gas industry faces numerous problems, from the exploration to the production phase. One of the most common problems faced by the industry is the formation of gas hydrates in the pipeline during the deep-water operation. The advancement of kinetic hydrate inhibitors (KHIs) has been rapid. However, as the natural degradation of conventional KHIs, such as polyvinylpyrrolidone (PVP) and polyvinylcaprolactam (PVCap), is challenging, there is a need to develop environmental-friendly KHIs with enhanced biodegradability to improve possible environmental risks. Thus, green inhibitors have been developed as a new class of KHIs. Research for enhancement of green hydrate inhibitors, as an alternative for existing low dosage hydrate inhibitors (LDHIs), has increased. In this paper, the effect of induction time with presence of cassava peels on the formation of methane hydrate was studied and compared with commercialized inhibitor, PVP. The performance of cassava peels as a kinetic hydrate inhibitor was investigated using high pressure micro differential scanning calorimetry (µ-DSC). For the induction time measurement, linear cooling ramps at a constant cooling rate of 0.5 K/min were used under isobaric conditions. Aqueous solutions of 0.5 wt % and 1.0 wt % of cassava peels were prepared and the induction time of methane hydrate formation in these solutions was measured at pressure ranges from 4.0 to 10.0 MPa. One of the characteristics to be a good kinetic inhibitor is the presence of hydroxyl functional group in inhibitors, which assist to form hydrogen bonds with water molecules, thus preventing hydrates formation. Fourier transform infrared (FTIR) analysis confirms the presence of hydroxyl groups in cassava peels with wavenumber value of 3370.68 cm−1. Cassava peel solution is observed to delay the induction times at all pressure settings and it is better at 1.0 wt % concentration. However, at lower pressures of 4 and 6 MPa, the performance is less effective when compared to a commercial inhibitor, PVP. At high pressures of 8 and 10 MPa, it can be seen that the performance is as effective as PVP. This research paper shows that cassava peels have high potential to be developed as a gas hydrate green kinetic inhibitor that can be applied for industry usage in the future.
Surfactant-based viscoelastic (SBVE) fluids have recently gained interest from many oil industry researchers due to their polymer-like viscoelastic behaviour and ability to mitigate problems of polymeric fluids by replacing them during various operations. This study investigates an alternative SBVE fluid system for hydraulic fracturing with comparable rheological characteristics to conventional polymeric guar gum fluid. In this study, low and high surfactant concentration SBVE fluid and nanofluid systems were synthesized, optimized, and compared. Cetyltrimethylammonium bromide and counterion inorganic sodium nitrate salt, with and without 1 wt% ZnO nano-dispersion additives, were used; these are entangled wormlike micellar solutions of cationic surfactant. The fluids were divided into the categories of type 1, type 2, type 3, and type 4, and were optimized by comparing the rheological characteristics of different concentration fluids in each category at 25 °C. The authors have reported recently that ZnO NPs can improve the rheological characteristics of fluids with a low surfactant concentration of 0.1 M cetyltrimethylammonium bromide by proposing fluids and nanofluids of type 1 and type 2. In addition, conventional polymeric guar gum gel fluid is prepared in this study and analyzed for its rheological characteristics. The rheology of all SBVE fluids and the guar gum fluid was analyzed using a rotational rheometer at varying shear rate conditions from 0.1 to 500 s−1 under 25 °C, 35 °C, 45 °C, 55 °C, 65 °C, and 75 °C temperature conditions. The comparative analysis section compares the rheology of the optimal SBVE fluids and nanofluids in each category to the rheology of polymeric guar gum fluid for the entire range of shear rates and temperature conditions. The type 3 optimum fluid with high surfactant concentration of 0.2 M cetyltrimethylammonium bromide and 1.2 M sodium nitrate was the best of all the optimum fluids and nanofluids. This fluid shows comparative rheology to guar gum fluid even at elevated shear rate and temperature conditions. The comparison of average viscosity values under a different group of shear rate conditions suggests that the overall optimum SBVE fluid prepared in this study is a potential nonpolymeric viscoelastic fluid candidate for hydraulic fracturing operation that could replace polymeric guar gum fluids.