Hemant Sagar

Dr. Hemant Sagar

Faculty of Mechanical Engineering, University of Duisburg-Essen, 47057 Duisburg, Germany

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
HSHemant Sagar
Hemant Sagar
Bettar O. El MoctarBettar O. El Moctar
Bettar O. El Moctar
Experiments were performed to investigate the collapse dynamics of a cavitating bubble generated between a pair of symmetrically arranged oblique plates. A 2.0 mm gap was left at the converging end of the two plates, which were inclined at an angle of 10°. A focused laser beam generated a cavitation bubble of about 4.0 mm in diameter, at four different locations that were placed on the centerline between the glass plates. A high-speed camera captured the bubble's cavitating dynamics at a frame rate of 75 kHz. The initial position of the bubble and, thus, the boundary conditions significantly influenced the bubble's dynamics. The bubble's first collapses showed a distinct unidirectional extended jetting but without notch formation on the bubble's left surface. Subsequent collapses led to intense nucleation, a feature useful in microfluidic devices. Further on, we observed vertical pillar-shaped cavities, floating toroids, etc., shapes that were rarely mentioned in previous investigations. To support our experimental results, we performed numerical simulations based on solving the Navier–Stokes equations, to replicate similar bubble dynamics. Our results provided insight into bubble dynamics generated between oblique plates, thereby potentially contributing to an improved understanding of microfluidic pumping techniques, surface cleaning devices, fouling of complex shapes, biomedical devices employing cavitation-based methods, and micromixing of fluids. Results of these experiments may serve also as benchmark data to validate numerical methods.

1 August 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
MLMing-Kang Li
Ming-Kang Li
SWShi-Ping Wang
Shi-Ping Wang
SZShuai Zhang
Shuai Zhang
HSHemant Sagar
Hemant Sagar
The current work experimentally studies the complex interaction between underwater explosion (UNDEX) bubbles and a free surface. We aim to reveal the dependence of the associated physics on the key factor, namely, the dimensionless detonation depth γ (scaled by the maximum equivalent bubble radius). Four typical bubble behavior patterns are identified with the respective range of γ: (i) bubble bursting at the free surface, (ii) bubble jetting downward, (iii) neutral collapse of the bubble, and (iv) quasi-free-field motion. By comparison of the jet direction and the migration of the bubble centroid, a critical value of γ is vital for ignoring the effects of the free surface on UNDEX bubbles. Good agreements are obtained between the experimental data and Zhang equation [Zhang et al., “A unified theory for bubble dynamics,” Phys. Fluids 35, 033323 (2023)]. Additionally, the dependence of the pressure signals in the flow field on γ is investigated. The peak pressure, impulse, and energy dissipation in the UNDEX are investigated.

21 May 2018 in Ship Technology Research
Verified
Journal Article
Closed access
HSHemant Sagar
Hemant Sagar
Bettar O. El MoctarBettar O. El Moctar
Bettar O. El Moctar
This paper documents the numerical investigation of the flow surrounding a collapsing laser-induced cavitation bubble with an initial radius of 1.45 mm. The three-dimensional laminar flow was captured by solving the Navier–Stokes equations. To account for the multiphase flow (water and vapour), the Volume of Fluid (VoF) method was used. The source term of the transport equation of the VoF function was based on the simplified Rayleigh–Plesset equation. The distance of the bubble from a solid surface wall was varied according to the dimensionless parameter D/Rmax ranging from 0.3 to 3.0, where Rmax is maximum bubble radius and D is the distance between bubble centre and solid surface. Computed collapse derivatives, impact velocity, impact pressure, and visual characteristics, such as toroidal shapes of oval impacts, agreed favourably to experimental measurements.

25 September 2024 in Scientific Reports
Verified
Journal Article
Open access
PDF file
HSHemant Sagar
Hemant Sagar
YLYuxing Lin
Yuxing Lin
OMOuld el Moctar
Ould el Moctar
Cavitation and its effects are well investigated, especially single bubble cavitation and its collapse near rigid and elastic boundaries. In our current article, we investigated novel experiments of a single cavitation bubble near an oscillatory boundary. We generated the cavitation bubble by laser focusing in water. A flat glass plate was fixed to the shaft of the magnetostriction oscillator coil. We investigated the dynamics of bubbles at two relative wall distances (ratio of the distance between the bubble center and plate surface to the maximum radius of the bubble) of the bubble from the glass plate in combination with four modes of oscillation. Each mode has specific frequency and amplitude of oscillation. The high-speed camera captured the dynamics of the bubble using the back-illumination method with a framing rate of 120Kfps and simultaneously we used an optical CMOS sensor to measure the oscillation of the glass plate. We presented a clear comparison among the bubble dynamics near stationary and oscillating plates with parameters such as oscillating modes and direction. We correlated the dynamics of the bubble with the motion of the plate. In addition, we highlighted the differences including the characteristics of bubble shape and jetting that occurred during the collapse phase. The comparison of the time histories of the bubble’s equivalent size postulated that the bubble’s collapse times vary significantly in some cases compared to the bubble’s dynamics near the stationary plate. In all cases, we noticed the shortening of the bubble’s collapsing time, i.e. accelerated collapses. In our findings, we noticed a collapse times reduction of about 4–15%. Our finding signifies the importance of introducing the oscillation of the boundaries to obtain effective energy concentration over the time during the collapse. Our study also suggests that forced oscillation of boundaries is undesirable for destructive cavitation effects. The method we suggested for the manipulation of bubble dynamics holds potential for enhancing the efficiency of applications such as lithotripsy in biomedical devices, actuation and micro pumping in microfluidic devices, and effective semiconductor surface cleaning. Not but least, obtained results can be used as benchmark in future for validating numerical methods.

1 January 2025 in Physics of Fluids
Verified
Journal Article
Closed access
QNQuang-Thai Nguyen
Quang-Thai Nguyen
Nguyen Van-TuNguyen Van-Tu
Nguyen Van-Tu
HSHemant Sagar
Hemant Sagar
Bettar O. El MoctarBettar O. El Moctar
Bettar O. El Moctar
WPWarn-Gyu Park
Warn-Gyu Park
The behaviors of a collapsing cavitation bubble were investigated using numerical simulations, focusing on the effects of a controlled oscillating wall with a spherically curved geometry. Different wall-controlled oscillation conditions were modeled. The collapse of the laser-induced cavitation bubble near the curved wall was observed experimentally to validate the numerical model at the same fixed standoff condition S = 1.2. A good agreement was observed between experimental and numerical results. A compressible model for the two-phase flow, based on a geometric volume of the fluid technique, was employed for numerical simulation. High-speed camera experiments captured the behaviors of the laser-induced cavitation bubbles. Both in-phase and out-of-phase oscillating motion of a rigid with spherical surface was modeled by using a sinusoidal function within a curvilinear moving grid framework. The study explored the effects of oscillating walls through numerical comparisons between the fixed and oscillating conditions, considering different initial phase conditions as φ0=−90°, 0°, φ0=+90°, and +180°. The upward jet flow forms at φ0=−90°, 0°, and +90°, while the downward jet flow forms at φ0=+180°. Numerical analyses reveal significant effects of motion conditions at in-phase (φ0=−90°, 0°) and out-of-phase (φ0=+90°, +180°) conditions, which vary with the scaled amplitude parameter, As=A/R0, defined by the ratio of the oscillating amplitude, A, and the maximum bubble radius, R0. Various features were analyzed, including oscillation and deformation of bubble shape, the formation of jet flow, and pressure peaks on the wall. Critical values of As = 0.1, 0.2, and 0.3 were identified, influencing bubble collapse time, jet flow speed, and peaks of pressure under both in-phase and out-oscillation motion.

28 May 2024 in Journal of Fluids and Structures
Verified
Journal Article
Closed access
HSHemant Sagar
Hemant Sagar
Bettar O. El MoctarBettar O. El Moctar
Bettar O. El Moctar